Onkyo TX-NR818 instruction manual En-95, USB Device Playback, Others

If you download or copy large files on your	—
computer, playback may be interrupted. Try closing
any unused programs, use a more powerful computer,
or use a dedicated server.
If the server is serving large music files to several	—
networked devices simultaneously, the network may
become overloaded and playback may be interrupted.
Reduce the number of playback devices on the
network, upgrade your network, or use a switch
instead of a hub.

■Can’t connect to the AV receiver from a Web browser

If you’re using DHCP, your router may not always	76
allocate the same IP address to the AV receiver, so if
you find that you can’t connect to a server or Internet
radio station, recheck the AV receiver’s IP address on
the “Network” screen.
Check the “Network” settings.	76

USB Device Playback

■Can’t access the music files on a USB device

Make sure the USB device is plugged in properly.	—
The AV receiver supports USB devices that support	108
the USB mass storage device class. However,
playback may not be possible with some USB devices
even if they conform to the USB mass storage device
class.

USB memory devices with security functions cannot — be played.

Others

■ Standby power consumption

In the following cases, the power consumption in 75, 77

standby mode may reach up to a maximum of

12.0 W:

–The “HDMI Control(RIHD)” setting is set to “On”. (Depending on the TV status, the AV receiver will enter standby mode as usual.)

–The “HDMI Through” setting is set to other than “Off”.

–The “Network Standby” setting is set to “On”.

If an MHL-enabled mobile device is connected to the 19 AUX (front) input, the power consumption in standby mode will increase.

■The sound changes when I connect my headphones

When a pair of headphones is connected, the listening — mode is set to Stereo, unless it’s already set to Stereo, Mono, Direct, or Pure Audio.

■The speaker distance cannot be set as required

The values entered may be automatically adjusted	—
with values best-suited for your home theater.

■ The display doesn’t work

The display is turned off when the Pure Audio	—
listening mode is selected.

■How do I change the language of a multiplex source

Use the “Multiplex” setting in the “Audio Adjust” 64 menu to select “Main” or “Sub”.

■The ufunctions don’t work

To use u, you must make an uconnection and an 21 analog audio connection (RCA) between the component and AV receiver, even if they are connected digitally.

En-95

Appendix

While Zone 2/3 is selected, the ufunctions don’t 21 work.

■The functions System On/Auto Power On and Direct Change don’t work for components connected via u

These functions don’t work when Zone 2/3 is turned 21 on.

■When performing Automatic Speaker Setup, the measurement fails and the message “Ambient noise is too high.” is displayed.

This can be caused by a malfunction in your speaker — unit. Check if the unit produces normal sounds.

■The following settings can be made for the composite video inputs

You must use the buttons on the unit to make these settings.

On the AV receiver, press the input selector for the input source that you want to set and the SETUP button simultaneously. While holding down the input selector button, press SETUP until “Video ATT :On” appears on the AV receiver’s display. Then, release both buttons. To turn the setting off, repeat the above process so that “Video ATT :Off” appears on the AV receiver’s display, and release the buttons.

• Video Attenuation

This setting can be made for the BD/DVD, CBL/SAT, STB/DVR, GAME 1, AUX, or USB input.

If you have a game console connected to the composite video input, and the picture isn’t very clear, you can attenuate the gain.

Video ATT :Off: The gain is not changed (default).

Video ATT :On: The gain is reduced by the values specified below.

–2 dB for the HDMI output.

–6 dB for the MONITOR OUT V output.