Specifications
Amplifier Section
Power output: | 75 W (8 Ω, 20 |
All channels: | 105 W (6 Ω, 1 kHz, DIN) |
| 130 W (6 Ω, 1 kHz, EIAJ) |
Dynamic power: | 2 x 180 W (3 Ω, front) |
| 2 x 150 W (4 Ω, front) |
| 2 x 95 W (8 Ω, front) |
THD (total harmonic |
|
distortion): | 0.08% (rated power) |
Damping factor: | 60 (front, 1 kHz, 8Ω) |
Input sensitivity and | 200 mV/47 k Ω (LINE) |
impedance: | |
Output level and | 200 mV/470 Ω (REC OUT) |
impedance: | |
Frequency response: | 10 |
| mode) |
Tone control: | ±12 dB, 50 Hz (BASS) |
| ±12 dB, 20,000 Hz (TREBLE) |
S/N ratio (Direct mode): 100 dB (CD, | |
Speaker impedance: | 6 Ω~ |
General
Power supply: | American model: AC 120 V, 60 Hz |
| Worldwide model: AC |
| 120 V switchable 50/60 Hz |
| Other models: AC |
| AC |
Power consumption: | American model: 4.6 A |
| Other models: 370 W |
Standby power |
|
consumption: | 2.5 W |
Dimensions |
|
(W x H x D): | |
| (435 x 150 x 376 mm) |
Weight: | American, European and Australian |
| models: 22.5 lbs. (10.2 kg) |
| Asian model: 24.3 lbs. (11.0 kg) |
■Video Inputs
Component video inputs:2 | (DVD, Video 1/2/3) | |
4 | (DVD, Video | |
Video inputs: | 4 | (DVD, Video |
Video Section
Input sensitivity, output
level and impedance: 1.0
0.7
0.28
1.0
Component video
frequency response: 5
Tuner Section
■FM
Tuning frequency range:
Usable sensitivity: | FM STEREO 17.2 dBf, 2.0 µV (75 Ω |
| IHF) |
| FM MONO 11.2 dBf, 1.0 µV (75 Ω IHF) |
S/N ratio: | FM STEREO 70 dB |
| FM MONO 76 dB |
THD: | FM STEREO 0.3% (1 kHz) |
| FM MONO 0.2% (1 kHz) |
FM stereo separation: | 45 dB at 1 kHz |
■AM
Tuning frequency range:
| |
Usable sensitivity: | 30 µV |
S/N ratio: | 40 dB |
THD: | 0.7% |
■Video Outputs
Component video |
|
|
outputs: | 1 | (Component Video Out) |
2 | (Video 1 Out, Monitor Out) | |
Video outputs: | 2 | (Video 1 Out, Monitor Out) |
■Audio Inputs
Digital inputs: | 4 | (Optical |
Analog inputs: | 6 | (CD, Tape, DVD, Video |
Multichannel analog |
|
|
inputs: | 5.1 ch (Front L/R, Center, Surround L/R, | |
|
| Subwoofer) |
■Audio Outputs
Analog outputs: | 2 (Tape Out, Video 1 Out) |
Subwoofer pre out: | 1 |
Speaker outputs: | 6+2 |
Phones: | 1 |
Specifications and features are subject to change without notice.
•The AV Receiver contains a microcomputer for signal processing and control functions. In very rare situations, severe interference, noise from an external source, or static electricity may cause it to lockup. In the unlikely even that this should happen, unplug the power cord from the wall outlet, wait at least five seconds, and then plug it back in again. That should fix it.
•To reset the AV Receiver to its factory defaults, turn it on and, while holding down the [VIDEO 1] button, press the [STANDBY/ON] button. “Clear” will appear on the display and the AV Receiver will enter Standby mode.
59
