Advanced
4 | Use the Left and Right [ | ]/[ ] |
| buttons to adjust the speaker | |
| level, and use the Down [ | ] but- |
| ton to select the next speaker. | |
The levels can be adjusted from
5 | Repeat step 4 so that the level of |
| |
| the test tone coming from each |
| speaker is the same. |
| Speakers that you set to No or None in |
| the Speaker Configuration (page 35) do |
| not output the test tone. |
|
|
6 | Press the [SETUP] button. |
| |
| Setup closes. |
| Don’t forget to turn down the volume if |
SETUP | you turned it up while setting the levels. |
|
|
Note:
•A quick way to adjust the speaker levels is to press the remote controller’s [TEST TONE] button to turn on the test tone, use the
Digital Input Signal Formats
The following table shows the display indicator for each digital signal format.
Format | Display | |||||
|
|
|
|
|
|
|
Dolby Digital |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
DTS |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PCM |
|
| PCM | |||
|
|
|
|
|
|
|
Normally, the AV receiver detects the signal format auto- matically. However, if you experience either of the fol- lowing issues when playing PCM or DTS material, you can specify the signal format as either PCM or DTS:
•If the beginnings of tracks from a PCM source are cut off, try the PCM setting.
•If noise is produced when fast forwarding or reversing a DTS CD, try the DTS setting.
|
|
|
|
|
|
|
|
|
|
| MASTER VOLUME |
| |
|
|
|
|
|
|
|
|
|
| TUNING | PRESET |
|
|
STANDBY/ON |
|
|
|
|
|
|
|
|
|
|
|
|
|
STANDBY |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ENTER |
|
|
MULTI CH |
| DVD | VIDEO 1 | VIDEO 2 | VIDEO 3 |
| TAPE | TUNER | C D | RETURN | SETUP |
|
|
|
|
| VCR |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| VIDEO 3 INPUT |
|
PHONES |
|
|
|
|
|
|
|
|
|
| VIDEO | L AUDIO | R |
SPEAKERS |
| TONE |
| STEREO | LISTENING MODE | DISPLAY | DIGITAL | DIMMER MEMORY | TUNING |
|
|
| |
A | B |
|
| INPUT | MODE |
|
|
| |||||
DIGITAL INPUT
1 | Press and hold the AV receiver’s [DIGITAL |
| INPUT] button for about 3 seconds. |
|
|
2 | While “Auto” is displayed (about 3 sec- |
| onds), press the [DIGITAL INPUT] button |
repeatedly to select: PCM, DTS, or Auto.
PCM: Only PCM format input signals will be heard. If the input signal is not PCM, the PCM indicator will flash and there will be no sound.
DTS: Only DTS format input signals will be heard. If the input signal is not DTS, the DTS indicator will flash and there will be no sound.
Auto (default): The format is detected automati- cally. If no digital input signal is present, the corresponding analog input is used instead.
52
