Handshaking, Buzzer Operation, Functions | Opticon LMD 1135 instruction

Manual No. 25-ULPNR102-01; Mar, 2005

LMD 1135 Laser Fixed Mount Scanner

	Handshaking
I0	Unlimited wait for CTS from terminal
I1	100 mS wait for CTS from terminal
I2	200 ms wait for CTS from terminal
I3	400 mS wait for CTS from terminal
P0	No Handshaking
P1	Busy/Ready
P2	Modem
P3	ACK/NAK (1 second timeout with error
	buzzer)
P4	ACK/NAK no response (100 ms timeout,
	terminates with good read buzzer)
ZG	XON/OFF
KA	No intercharacter delay
KB	20 ms intercharacter delay
KC	50 ms intercharacter delay
KD	100 ms intercharacter delay

	Buzzer Operation
T0	Volume = Maximum
T1	Volume = Upper mid-range
T2	Volume = Lower mid-range
T3	Volume = Minimum
W0	Disable Buzzer
W1	Enable buzzer at 3kHz
W2	Enable buzzer at 3kHz with 2.5kHz interval
W3	Enable buzzer at 3kHz with 4kHz interval
W4	Buzzer duration 0.10 sec
W5	Buzzer duration 0.20 sec
W6	Buzzer duration 0.40 sec
W7	Buzzer duration 0.05 sec
W8	Enable buzzer

	Positive & Negative Bar Codes
V2	Positive bar codes only
V3	Only negative bar codes
V4	Both positive and negative bar codes

	Setting the Trigger & Auto-Trigger
	Functions
S7	Disable the trigger function (Laser On)
S8	Enable the trigger function (Laser OFF until
	the trigger is activated )
+F	Auto-Trigger Disable
+I	Auto-Trigger Enable
Z	Activate the trigger; turns the laser ON

		Selecting the Read Mode
S0		Single Read Mode (Trigger must be Enabled,
		S8)
S1		Multiple Read Mode
S2		Continuous Read Mode

		Parallel Read Mode

+6		2 Parallel labels only
+7		3 Parallel labels only
+8		4 Parallel labels only

Page 22

Image 26

Opticon LMD 1135 Handshaking, Buzzer Operation, Positive & Negative Bar Codes, Setting the Trigger & Auto-Trigger

Contents

Manual No -ULPNR102-01 March OSE Command Set User’s ManualPage Contents Scanner Servicing and Maintenance Technical SpecificationsConfiguring the Scanner Introduction and Getting Started Product Overview Quick Start-Up ProcedureSection Introduction and Getting Started Page Optical Specifications Section Technical SpecificationsPhysical Specifications Avoid specular reflection in the dead zone +/- 8 degrees Electrical Specifications JAN 13 R = 30 mm 1.2 or RS232 Signal Level RS232 Communications SpecificationsConnector Pin-outs RS232 Transmit / Receive Character Format Ordering Information Environmental SpecificationsPin No Signal Model Distance to the Bar Code Section Positioning the Scanner for Optimum PerformanceAchieving Optimum Performance Depth-of-Field Avoiding Specular Reflection Distance Max From Window Width Measuring Scanner Performance Quality Bar Code Labels Application Notes Tips for Achieving High Throughput Tips for Insuring Highest Data Integrity Tips for Verifying the Presence of a Bar Code Default Settings Section Configuring the ScannerProgramming Menus & Commands Parameter Factory Default Setting Common Causes of Poor Performance Section Application Engineering SupportTechnical Assistance and Support Modified and/or Customized Scanners IEC 825-1 Class 1 Laser Device Section Scanner Servicing and MaintenanceSection Scanner Labeling Appendices ESC Computer Command CR Appendix a Reset All Defaults U2 Command U2 What if you make a mistake? Options for UPC Global DefaultsSymbology Selection Options for EAN-8 & EAN-13 Options for Code Prefix/Suffix of Numeric Characters Select Symbology forPrefix/Suffix Prefix/Suffix of Alpha Characters Parallel Read Mode Setting the Trigger & Auto-TriggerSelecting the Read Mode Handshaking Mode Scanner Timeout Trigger EnabledXmit Error Trigger Enabled Mode only Quiet Zone Options Appendix C Computer Global Default & Scanner ConfigurationsCommand Description Including prefix/suffix Symbologies Symbology SelectionDescription Command Bar Code Only EAN 13/8 +2 Add/Activate Specific Bar Code Symbologies START/END Disable all symbologies Delete/Deactivate Specific Bar Code SymbologiesAdd/Activate Specific Bar Code Symbologies Bar Code Command Description Options for UPC Options for EAN-8 & EAN-13 Options for Code 39 & IT Pharmaceutical IT Pharmaceutical, enable Transmit of leading a Options for Codabar NW-7 Codabar NW-7 Format Options for Interleaved & Industrial 2 5 Format Standard and Interleaved Meaning of Acronym Options for IataString format Number of digits 15 total Options for Code-128 / EAN-128 Options for Code-93 Disable fixed length all Fixing the Number of Digits Creating a Prefix and/or Suffix Setting Prefixes Identifying the Symbology UPC-E +2 or +5 MSI/Plessey Setting Suffixes Identifying the Symbology Bar Code Command Description Direct Input of Numeric Characters Direct Input of Alpha Characters Direct Input of Alpha Characters Lower Case ETB Direct Input of Control Characters SUB Direct Input Characters Misc Bar Code Command Description Code Identification & Characters/Digits Transmitted START/END Communication Parameters Communication Parameters Handshaking Terminal Ms intercharacter delay Disable buzzer Buzzer Operation Setting the Trigger & Auto-Trigger Functions Positive & Negative Bar Codes Selecting the Read Mode Trigger Function Enabled S8 Trigger Function Disabled S7 Parallel labels only Parallel Read ModeAdd-on Wait Mode Applies to UPC/EAN only Scanner Timeout Trigger Enabled Mode only Multiple Read Reset Time Quiet Zone Options Redundant Decoding Transmitting Error Indications Trigger Enabled only Error Messages No decode / no label Good Read LED Operation Appendix D Appendix E