1001

8.7D.H.W. Burner Pressure

The domestic hot water burner pressure is not range rateable and not adjustable but the maximum and minimum burner pressure should be checked as follows:

a.Check electricity supply is still off.

b.Open a D.H.W. tap at high flow until the water runs cool and leave running.

c.Switch on the electricity supply.

d.The pressure should be 14 mbar -/+ 0.5 mbar.

e.Disconnect one of the wires from the «Modureg» (fig. 22), this will reduce the burner to minimum

which should read

3.0 mbar +/- 0.5 mbar. If the burner pressure is not as stated check the

inlet working pressure (fig. 22) which should be

minimum 20 mbar. If that is correct, consult Ferroli.

No attempt should be made to alter D.H.W. burner pressure.

f.Switch off electrical supply and close hot tap.

g.Reconnect the wire to the «Modureg». Remove pressure gauge, tighten the test screws.

h.Replace control panel (2 screws).

i.Turn on electricity supply, open a hot tap to full flow and when the burner lights, test for gas soundness

with a leak detection

fluid around the gas valve and connections including the pressure test point

screws.

 

9.0SYSTEM OPERATION

Let the boiler operate normally on central heating for about 30 minutes.

I)Vent radiators.

II)Vent heat exchanger.

III)Examine all pipework for leakage.

IV) Turn on a D.H.W. tap and check that the C.H. pump stops running.

V)As the D.H.W. temperature reaches 60°C check the burner for modulation. Switch off electricity.

Drain down the central heating system fully, when hot.

Refill the system as previously instructed. Repeat the venting. Examine the system's water pressure and top up as necessary. Replace the casing front panel and close the control panel cover.

10.0HANDING OVER TO THE USER

After completion of installation and commissioning of the system:

a.Hand over the User's Instructions' to the Householder and explain His/Her responsability under the Gas safety (Installation and Use) Regulations 1994.

b.Explain and demonstrate the lighting and shutting down procedure.

c.Explain the operation of the boiler including the use and adjustment of ALL system controls. Advise the User of the precautions necessary to prevent damage to the system and to the building, in the event of the system remaining inoperative during frost conditions.

d.Stress the importance of regular servicing by a qualified Heating Engineer and that a comprehensive service should be carried out at LEAST ONCE A YEAR.

24

Page 23 Page 25
Page 24
Image 24
Optima Company 1001 installation instructions D.H.W. Burner Pressure, System Operation, Handing Over to the User
Page 23 Page 25

1001 specifications

Optima Company 1001 stands at the forefront of innovation, showcasing a remarkable blend of advanced technology and user-centric design. Founded with the vision of revolutionizing the industry, Optima has quickly positioned itself as a leader in producing high-performance solutions that cater to a diverse clientele.

One of the main features of Optima Company 1001 is its commitment to sustainability. The company has integrated eco-friendly practices into its manufacturing processes, allowing for reduced waste and lower energy consumption. This not only benefits the environment but also enhances the overall efficiency of its products. By utilizing recyclable materials and implementing sustainable sourcing practices, Optima ensures that it remains at the cutting edge of corporate responsibility.

Another hallmark of Optima Company 1001 is its dedication to technological advancement. The firm employs state-of-the-art technologies that resonate with the demands of modern consumers. This includes the use of artificial intelligence and machine learning to optimize operational efficiency and personalize user experiences. Through data analytics, Optima is able to anticipate trends and adapt its offerings, ensuring that customers always receive the most relevant solutions.

Durability and reliability are pivotal characteristics of products manufactured by Optima Company 1001. Each product undergoes rigorous testing to meet high standards of quality and performance. This commitment to excellence means that customers can trust in the longevity and functionality of the products they purchase, giving them peace of mind in their investment.

User-friendliness is also a defining trait of Optima’s offerings. The company places great emphasis on design, ensuring that products are intuitive and accessible to users. This focus on usability is reflected in straightforward interfaces and ergonomic designs that enhance the overall user experience.

Furthermore, Optima Company 1001 prioritizes customer service, providing comprehensive support throughout the product lifecycle. This includes installation assistance, maintenance services, and a robust warranty program, underscoring the company’s dedication to customer satisfaction.

In summary, Optima Company 1001 is characterized by its innovative technologies, commitment to sustainability, product reliability, user-centric design, and exemplary customer service. These features collectively enhance its reputation as an industry leader and pioneer in delivering solutions that are not only high-quality but also aligned with the needs and values of today’s consumers.
Top Page Image Contents