Manuals / Oregon Scientific / Communications / Cordless Telephone

Oregon Scientific OS6976 user manual Charging The Battery, Display Messages

Models: OS6976

1 46

Download 46 pages 3.28 Kb

Page 38

CHARGING THE BATTERY

EN

CHARGING THE BATTERY

Make sure the telephone is OFF before you replace battery.

1.Remove the battery compartment door.

2.Disconnect the battery plug from the jack in the handset battery compartment and remove the battery pack.

3.Connect the plug of the new battery pack into the jack inside the handset, and then insert the new battery pack into the compartment.

4.Close the battery compartment by pushing the cover up until it snaps into place.

5.Place handset in the Charge to charge. Allow the handset battery to properly

charge (for 12 hours) prior to first use or when you install a new battery pack. If you do not properly charge the phone, battery performance will be compromised.

CAUTION: To reduce the risk of fire or personal injury, use only Oregon Scientific’s battery .

DISPLAY MESSAGES

The following indicators show the status of a message or of the unit.

INCOMPLETE DATA	Caller information has been interrupted during transmission or the phone
	line is excessively noisy.
ENTER NAME	Prompt telling you to enter the name for one of the 10 memory locations.
ENTER TEL NUMBR	Prompt telling you to enter the telephone number for one of the 10
	memory locations.
PRESS AND HOLD	Prompt telling you to re-register the handset or the Spacemaker® to the
FORMAT KEY	wall base unit.
PRESS AND HOLD	Indicates to press the page button on the wall base unit to complete the
BASE PAGE KEY	registration of either the handset or the Spacemaker®.
DELETE?	Prompt asking if you want to erase Caller ID records or one of the 10
	numbers stored in the phone’s outgoing memory.
DELETE ALL?	Prompt asking if you want to erase all Caller ID records.
DELETED	Prompt confirming the Caller ID /Memory record is erased.
END OF LIST	Indicates that there is no additional information in Caller ID memory.
BLOCKED NUMBER	The callers telephone number is blocked from transmission.
LINE IN USE	Indicates that either the handset or the Spacemaker® or another phone
	connected to the same line is in use.
NEW	Indicates call or calls have not been reviewed.
UNKNOWN NAME/	The incoming call is from an area not serviced by
CALLER/NUMBER	Caller ID or the information was not sent.
PAGING	Someone has pressed the page button on the base.

35

os6976-en1.p65

38

5/6/2005, 10:33 AM

Image 38

Oregon Scientific OS6976 user manual Charging The Battery, Display Messages

Contents

os6976-en1.p65 Model OS6976 User Manual Manual de Usuario900MHz Cordless Phone with Kitch Companion 5/6/2005, 1032 AMUser Manual TABLE OF CONTENTS900MHz Cordless Phone with Kitchen Companion Model OS6976 Speakerphone Guidelines IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTION INTRODUCTION DIGITAL SECURITY SYSTEMSAFTEY PRECUATIONS PARTS CHECKLISTBEFORE YOU BEGIN TELEPHONE JACK REQUIREMENTS INSTALLATION GUIDELINESINSTALLING THE PHONE INSTALLING THE HANDSET BATTERY CONNECTING THE TELEPHONE LINECONNECTING THE AC ELECTRICAL POWER PRIOR TO USEUNDER CABINET MOUNTING CHARGING THE HANDSET BATTERYCHARGE UNIT TOOLS REQUIREDMOUNTING HARDWARE PACKED WITH YOUR UNIT BEFORE MOUNTINGIf your cabinet has an overhang MOUNTING PROCEDURE1. If your cabinet does not have an overhang 4. If your cabinet does NOT have an overhang, go to Step If your cabinet does not have an overhang, go to Step message HANDSET AND WALL BASE UNIT LAYOUTCHARGE UNIT LAYOUT tune/seek +ADJUST THE DAY OF THE WEEK CHARGE UNIT SETUPDAY/TIME SETUP ADJUST THE HOURSET LANGUAG ENG FRA RINGER SETUPSYSTEM SETUP SET AREA COSET ANSWERE ON OFF SET TONE/PUL TONE PSET CONTRAS TONE/PULSE DIALINGRING TO ANS SETTING THE RINGS TO ANSWERSETTING THE SECURITY CODE FOR REMOTE ACCESS SECURITY CO 1 2RINGER SETT HIGH LOW DEFAULT SETT YES NODEFAULT SETTINGS HANDSET UNITLANGUAGE SET RINGERSYSTEM SETUP LOCAL AREA CODEDEFAULT SETTINGS HANDSET OPERATIONREGISTRATION TONE/PULSE DIALINGLINE IN USE RECEIVING A CALLMAKING A CALL 3-WAY CONFERENCINGAUTO STANDBY IN USE INDICATOR LIGHTFLASH CHANNEL BUTTONSPEAKERPHONE OPERATION VOLUMECALL TIMER RINGERMAKING A CALL CALL TRANSERRECEIVING A CALL LINE IN USESPEAKERPHONE VOLUME SPEAKER INDICATOR LIGHTCHARGE INDICATOR LIGHT CH 22VOICE INSTRUCTIONS MESSAGES INDICATORANSWERING SYSTEM OPERATION RECORDING THE OUTGOING ANNOUNCEMENTANSWERING SYSTEM MEMORY FULL REMOTE ACCESSMESSAGE PLAYBACK ERASING MESSAGESTo Press this button CALLER ID CIDCALL WAITING CALLER ID during message playbackTRANSFERRING CID RECORDS TO MEMORY RECEIVING AND STORING CALLSREVIEWING CID RECORDS DIALING A CID NUMBER DELETING THE CID RECORD SHOWING IN THE DISPLAYDELETING ALL CID RECORDS CHANGING THE CID NUMBER FORMATUSING PRESET STATIONS RADIO VOLUMESTORING PRESET STATIONS RADIO OPERATIONCHANGING A STORED NUMBER MEMORYSTORING A NAME AND NUMBER IN MEMORY STORING A REDIAL NUMBERREVIEWING AND DELETING STORED NUMBERS DIALING A STORED NUMBERINSERTING A PAUSE IN THE DIALING SEQUENCE To replace a number stored in a memory location with a redial numberLong distance access number PROGRAMMABLE TIMERSETTING THE TIMER Authorization codePAUSING THE TIMER STARTING THE TIMERSTOPPING THE TIMER USING THE TIMER WITH OTHER MODESCHARGING THE BATTERY DISPLAY MESSAGESSignal HANDSET SOUND SIGNALSCONNECTING AN OPTIONAL HEADSET TO THE HANDSET Signals an incoming callCALLER ID TROUBLESHOOTING TIPSCONNECTING THE BELT CLIP TELEPHONEPage ABOUT OREGON SCIENTIFIC FCC STATEMENTCONSUMER INFORMATIONS This equipment is hearing aid compatible DECLARATION OF CONFORMITY Declare that the productos6976-en1.p65 2005 Oregon Scientific. All rights reserved086-003759-017 5/6/2005, 1033 AM