Smart Projection Clock with Mirror
Projector and LED Display
Model: RRM612P / RRM612PU /
RRM612PA
USER MANUAL
EN
OVERVIEW
INNER VIEW
| 1 |
6 |
|
5 | 2 |
| 3 |
| 4 |
1.FOCUS wheel: adjust projection focus
2.ALARM ON/OFF slide switch: enable or disable alarm
3.SLEEP: activate sleep timer
4.1, 2, 3, 4: preset radio stations
5.RADIO ON/VOL 
: turn on radio; increase radio volume
6.RADIO OFF/VOL
: turn off radio; decrease radio volume
BOTTOM VIEW
| 1 | |
9 | 2 | |
3 | ||
| ||
8 | 4 | |
| ||
7 |
| |
| 5 | |
| 6 |
1.SNOOZE buttons: snooze alarm; turn on projection
2.UP/TUNE +: increase value during setting; increase frequency during radio scan
3.DOWN/TUNE
4.Battery compartment
5.RESET: reset unit to default settings
6.RCC CLOCK ON/OFF slide switch: enable or disable clock signal reception
7.PROJECTION ON/OFF slide switch: enable or disable projection
8.ALARM: set alarm
9.CLOCK: set clock
LED DISPLAY
1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
109
1.Clock signal reception indicator
2.AM/PM indicator
3.Alarm icon
4.Sleep timer icon
5.Melody icon
6.Radio icon
7.Volume indicator
8.Low battery indicator
9.Time with hour and minute
10.Time zone indicator
BACK VIEW
D C 6 V |
1 |
1.Power adaptor
GETTING STARTED
The product should be powered by the AC/DC adaptor. Plug the adaptor into socket. Make sure it is not obstructed and is easily accessible to the unit.
To completely disconnect from power, the adaptor should be disconnected from the main unit.
NOTE The main unit and adaptor should not be exposed to wet conditions. No objects filled with liquid, such as vases, should be placed on the main unit and adaptor.
Battery serves only as memory backup.
1.Remove the battery compartment cover.
2.Insert the battery, matching the polarities.
NOTE Batteries should not be exposed to excessive heat such as sunshine or fire.
indicates battery is low.
CLOCK
CLOCK RECEPTION
This product is designed to synchronize its clock automatically with a clock signal.
RRM612P:
EU:
RRM612PU:
UK:
RRM612PA:
To enable / disable clock signal reception:
Switch RCC CLOCK ON/OFF slide switch to ON to enable or OFF to disable clock signal reception.
When clock signal reception is enabled (RCC CLOCK ON/OFF slide switch is ON), reception will occur regularly at 01:00, 02:00 and 03:00, or 3 minutes after every reset of unit. During reception, display will be temporarily off and
only a flashing will be shown. Display will resume after the reception, or upon pressing of any key, display will be temporarily on for 10 seconds.
Clock signal reception indicator:
SUCCESSFUL RECEPTION | FAILED RECEPTION |
-
NOTE
•Reception takes
•During reception, pressing any button or turning on the radio will stop the reception temporarily. Reception will resume if no more button is pressed after 10 seconds or the radio is turned off.
•If the radio is playing during reception time, reception will not occur.
MANUALLY SET CLOCK
1.Press and hold CLOCK.
2.Press UP/TUNE + or DOWN/TUNE - to increase or decrease values.
3.Press CLOCK to confirm.
4.The settings order is: time zone, 12/24 hr format, hour and minute.
RRM612P / RRM612PU: Time zone sets the clock +/- 23 hours from the received clock signal time. If you have disabled the clock signal reception, do not set a value for time zone.
RRM612PA: Select the time zone: (0) Pacific, (+1) Mountain, (+2) Central or (+3) Eastern.
PROJECTION
IMPORTANT If projection is illuminated, do not look directly into the projector or on the reflection from the mirror.
•To enable continuous projection:
Slide PROJECTION ON/OFF slide switch to ON and open the top cover.
•To focus image: Turn FOCUS wheel.
•To disable projection:
Slide PROJECTION ON/OFF slide switch to OFF. But, if the top cover is opened, pressing SNOOZE can turn on the projection for 5 seconds.
ALARM
To set alarm:
1.Slide ALARM ON/OFF slide switch to ON.
2.Press and hold ALARM.
3.Press UP/TUNE + or DOWN/TUNE - to set values for hour and minute.
4.The settings order is: hour, minute, Melody alarm or Radio alarm.
•If Melody alarm is selected, press UP/TUNE + or DOWN/ TUNE - to select Melody 1 / Melody 2 / Melody 3 / buzzer.
•If Radio alarm is selected, press UP/TUNE + or DOWN/ TUNE - to select radio station and press ALARM to confirm, then press UP/TUNE + or DOWN/TUNE - to adjust the volume.
5.Press ALARM to confirm. 
indicates alarm is on.
To activate / deactivate alarm:
Press ALARM.
To display alarm time:
Press ALARM. After 10 seconds, the display will resume to clock or radio.
To silence alarm:
•Press SNOOZE to silence it for 8 minutes.
OR
•Press any other button to turn the alarm off and activate it again after 24 hours.
FM RADIO
To play the radio:
1. Press and hold RADIO ON/VOL | . |
2.Press UP/TUNE + / DOWN/TUNE - to select radio frequency (press and hold to enable
To save a radio station:
Press and hold 1, 2, 3 or 4 while on a frequency. A total of 4 stations can be stored.
To adjust radio volume: |
| |
Press repeatedly | RADIO ON/VOL | to increase or |
RADIO OFF/VOL | to decrease volume. | |
To turn off radio: |
|
|
Press and hold RADIO OFF/VOL | . | |
RADIO SLEEP TIMER
The radio is equipped with a countdown sleep timer that can be set to switch the radio off after up to 120 minutes.
1.Press SLEEP to activate sleep timer. The radio turns on with the previous setting (radio frequency, volume and timer).
2.To change the sleep timer setting (120, 90, 60, 45, 30, 15, 0), press SLEEP. The sleep timer setting will be automatically activated.
NOTE If no button is pressed after 10 seconds, the unit will resume clock display.
RESET
Press RESET to return to the default settings.
PRECAUTIONS
•Do not subject the unit to excessive force, shock, dust, temperature or humidity.
•Do not cover the ventilation holes with any items such as newspapers, curtains etc.
•Do not immerse the unit in water. If you spill liquid over it, dry it immediately with a soft,
•Do not clean the unit with abrasive or corrosive materials.
•Do not tamper with the unit’s internal components. This invalidates the warranty.
•Only use fresh batteries. Do not mix new and old batteries.
•Images shown in this manual may differ from the actual display.
•When disposing of this product, ensure it is collected separately for special treatment.
•Placement of this product on certain types of wood may result in damage to its finish for which Oregon Scientific will not be responsible. Consult the furniture manufacturer's care instructions for information.
•The contents of this manual may not be reproduced without the permission of the manufacturer.
•Do not dispose old batteries as unsorted municipal waste. Collection of such waste separately for special treatment is necessary.
•Please note that some units are equipped with a battery safety strip. Remove the strip from the battery compartment before first use.
NOTE The technical specifications for this product and the contents of the user manual are subject to change without notice.
NOTE Features and accessories will not be available in all countries. For more information, please contact your local retailer.
SPECIFICATIONS
TYPE |
| DESCRIPTION | |
L x W x H | 100 x 100 x 100 mm | ||
(3.94 x 3.94 x 3.94 in) | |||
| |||
Weight | 460 g (16.2 oz) without battery | ||
Preset FM | 4 |
| |
radio memory |
| ||
stations |
|
| |
| • | ||
Alarm |
| radio alarm or | |
| melody or buzzer alarm | ||
|
| ||
| • | ||
|
| ||
Power | • 1 x CR2032 battery (for backup) | ||
• DC 6V 500mA adaptor | |||
| |||
ABOUT OREGON SCIENTIFIC
Visit our website (www.oregonscientific.com) to learn more about Oregon Scientific products. If you’re in the US and would like to contact our Customer Care department directly, please visit:
www2.oregonscientific.com/service/support
For international inquiries, please visit:
www2.oregonscientific.com/about/international
EU-DECLARATION OF CONFORMITY
Hereby, Oregon Scientific, declares that this Smart Projection Clock with Mirror Projector and LED Display (model: RRM612P / RRM612PU / RRM612PA) is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. A copy of the signed and dated Declaration of Conformity is available on request via our Oregon Scientific Customer Service.
COUNTRIES RTTE APPROVED COMPLIED All EU countries, Switzerland CH and Norway N
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio / TV technician for help.
DECLARATION OF CONFORMITY
The following information is not to be used as contact for support or sales. Please visit our website at www2. oregonscientific.com/service for all enquiries.
We |
|
Name: | Oregon Scientific, Inc. |
Address: | 19861 SW 95th Ave.,Tualatin, |
| Oregon 97062 USA |
Telephone No.: | |
declare that the product | |
Product No.: | RRM612P / RRM612PU / |
| RRM612PA |
Product Name: | Smart Projection Clock with |
| Mirror Projector and LED Display |
Manufacturer: | IDT Technology Limited |
Address: | Block C, 9/F, Kaiser Estate, |
| Phase 1,41 Man Yue St., |
| Hung Hom, Kowloon, |
| Hong Kong |
is in conformity with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation.
