Set Up and Troubleshooting

Step 3 Run all the wires from the amplifier location to the speakers, source unit, and bat- tery.. Do not connect the battery at this time.. Be sure to run RCAs and power and speaker wires away from factory electrical wires and system as they pose a great potential for induced system noise..

Step 4 Pre-drill amplifier mounting holes.. Be sure to "think before you drill".. Gas tanks, fuel lines, and other obstructions have a nasty way of hiding themselves.. For best results use a marking pen to mark the mounting holes and pre-drill these holes with a standard 1/8" drill bit..

Step 5 Mount the amplifier.. Make sure the amplifier is mounted on a flat surface.. If this is not possible, do not over tighten the screws so that the chassis of the amplifier is twisted or bent..

Step 6 Turn the vehicle's key switch to the off position.. Step 7 Disconnect the vehicle's battery ground terminal..

Step 8 Connect power wires to the amplifier (ground first, then 12 V(+) and REM)..

Step 9 Connect the RCA and speaker wires to the amplifier.. Check the quality of your speakers and signal connections.. This will determine the ultimate performance of your Orion Cobalt amplifier.. Refer to the Signal Input and Output Level Controls and Speaker Connections sections of this guide for correct wiring instructions..

Step 10 Reconnect the ground terminal to the battery after power, speaker, and RCA con- nections are completed..

Step 11 Set crossovers.. Refer to the Internal Crossover Configuration section of this manual for detailed instructions..

Step 12 Once satisfied that all connections and settings are correct, install the fuse located near the vehicle's battery and proceed to the Testing the System section of this manual..

WARNING! Never exceed the recommended fuse size of this amplifier.. Failure to do so will result in the voiding of your warranty and possible damage to the amplifier..

Testing the System

After you have completed the installation, you need to test the system.. This will help ensure years of trouble-free operation.. Please refer to the listed steps below when testing the sound of your Orion Cobalt system..

Step 1 Check all the wiring connections to be sure they are correct and secure..

Step 2 Turn the signal source volume control all the way down.. Set any tone controls to their flat or defeated positions.. This includes the loudness control..

Step 3 Turn the level controls of the amplifier to their minimum positions..

Step 4 Turn the source unit on.. Check to see if the power LED located on the input side of the amplifier is on.. If not, please refer to the Power Connections and the Troubleshooting Tips sections of this manual for instructions..

Step 5 If using an aftermarket source unit, turn the level controls of the amplifier about one quarter of a turn.. Slowly increase the volume level of the source unit to so that you can hear the output of the system.. If no sound is heard or if the output is dis- torted, turn the system off immediately.. Refer to the Power Connections and the Troubleshooting Tips sections of this manual to solve your installation problems..

Step 6 Check to make sure the output for each channel is correct.. If the active crossovers

C0600.2, C0300.2, Amplifier specifications

Orion Car Audio has been synonymous with powerful and high-quality sound amplification for years, and their amplifiers C0300.2 and C0600.2 exemplify this legacy. Designed for car audio enthusiasts looking for robust performance and reliability, these models are packed with innovative features that ensure an exceptional listening experience.

The Orion C0300.2 is a compact yet powerful two-channel amplifier that delivers a peak power output of 300 watts. It is engineered with a Class AB topology, combining the efficiency of Class D with the audio fidelity of Class A, making it suitable for a variety of audio systems. Its adjustable gain control allows users to fine-tune the amplifier to match their specific car stereo setup, ensuring that every note is crisp and clear. The C0300.2 also incorporates a built-in crossover system that lets users set the frequency range for each channel, resulting in optimized sound output tailored to the speakers being used.

On the other hand, the C0600.2 amplifier steps things up with a more powerful output, reaching a peak of 600 watts across its two channels. This amplifier is ideal for those who desire a high-impact audio experience, delivering deep bass and pristine highs. Similar to its counterpart, the C0600.2 employs a Class AB design, allowing for high efficiency and better thermal management. This feature ensures that even during extended playback, the amplifier remains cool, preventing overheating and potential damage to the internal components.

Both amplifiers boast a sleek design with a durable chassis, providing not only robust performance but also an aesthetic that fits well within modern car interiors. The integrated short circuit and thermal protection circuits safeguard the amplifier against potential damage, adding to the reliability that Orion is known for.

In addition to their powerful output and efficient designs, both models offer flexibility in installation with multiple mounting options and a user-friendly interface. These features make the C0300.2 and C0600.2 amplifiers perfect choices for anyone looking to enhance their vehicle's audio system, delivering performance that meets the demands of car audio enthusiasts everywhere.

With features designed to maximize sound quality and system compatibility, the Orion Car Audio amplifiers stand as a leading choice for those who appreciate superior audio performance in their vehicles. Whether for daily commuting or enjoying long road trips, these amplifiers elevate the driving experience to a whole new level.

Orion Car Audio Amplifier, C0600.2, C0300.2 Set Up and Troubleshooting, Testing the System

Models: C0600.2 C0300.2 Amplifier