Manuals / Orion Car Audio / Car Audio and Video / Car Stereo System

Orion Car Audio XTREME 600.4 owner manual System Planning, page, Amplifier

Models: XTREME 600.4

1 44

Page 17

SYSTEM PLANNING

SYSTEM 4

System 4 is a four-way quad-amplified system. Amplifier 1 is bi-amplified for the front separates. Amplifier 2 is configured for two-way operation. The front channels are configured for two 4-ohm midbass drivers. The rear channels are configured two 4 ohm subwoofers. The RGC-1 controls the subwoofer level from the dashboard of the vehicle.

Amplifier 1

Lowest recommended impedance is 2 ohms stereo operation

Front channels are configured for stereo operation

Front channels are configured for bandpass operation

Rear channels are configured for stereo operation

Rear channels are configured for high-pass operation

Amplifier 2

∙Lowest recommended impedance in 2 ohms stereo

∙Front channels are configured for stereo operation

∙Front channel input configured for bandpass operation

∙Rear channels configured for summed stereo operation

∙RGC –1 connected to rear gain point controls bass level for the system

page 17

Page 17

Image 17

Orion Car Audio XTREME 600.4 owner manual System Planning, page, Amplifier

Contents

XTREME OWNER’S MANUALTABLE OF CONTENTS page I N T R O D U C T I O NRECORD YOUR SERIAL NUMBER AND DATE ABOUT THIS MANUALPRACTICE SAFE SOUND 1 XTREME amplifier 1 4 gauge power and ground connector WHAT’S IN THE BOX1 12 gauge speaker and remote connector 1 XTREME installation and operation manualWARRANTY ORION Industries Inc ATTN. Repair Department 9235 South McKemy Street Amplifier Section SPECIFICATIONSXTREME 600.4 Front Channels XTREME 600.4 Rear Channels4 All crossovers are with a slope rate of 12dB/octave and a “Q” of XTREME 600.4 Front ChannelsXTREME 600.4 Rear Channels XTREME TECHNICAL DESIGN FEATURES1. Power LED - lights up when the amplifier is on TECHNICAL DESIGN FEATURESSYSTEM PLANNING RGC-1 SYSTEM PLANNINGAmplifier AmplifierSYSTEM PLANNING RGC-1SYSTEM SYSTEM PLANNINGpage AmplifierSYSTEM PLANNING RGC-1SYSTEM SYSTEM PLANNINGpage AmplifierINSTALLATION POWER CONNECTIONS SPEAKER CONNECTIONS page 3-CHANNEL STEREO/BRIDGED CONFIGURATIONSPEAKER CONNECTIONS Lowest recommended impedance for both front and rear channels is 4Ω SPEAKER CONNECTIONSSPEAKER CONNECTIONS Front and rear outputs must be configured for stereo operationLowest recommended impedance is 2Ω stereo and 4Ω bridged mono Front and rear outputs must be set for full range operation4-CHANNEL AMPLIFIER INPUT CONFIGURATIONS OUTPUT CONFIGURATIONSRCA INPUT / CH 1 & 2 XVR REAR INTERNAL CROSSOVER CONFIGURATIONWhen the switch is in the right position, the crossover is configured for low-pass operation. The rear channels of the XTREME 600.4 are continuously variable from 45Hz to 5kHz FRONT INTERNAL CROSSOVER CONFIGURATIONREAR INTERNAL CROSSOVER CONFIGURATION When the puch button switch is in the “off” position, the high-pass crossover is bypassed FRONT INTERNAL CROSSOVER CONFIGURATION2,500Hz 3,500Hz 85Hz FINE TUNING INTERNAL CROSSOVER1,200 Hz 10 kHzThe difference of INTELLi Q INTELLI QBoost Levels INTELLI QREMOTE GAIN SIGNAL INPUT AND OUTPUT LEVEL CONTROLSPASSENGER COMPARTMENT GENERAL PRECAUTIONS AND INSTALLATION TIPS STEP BY STEP INSTALLATION TESTING THE SYSTEM ADJUSTING THE SOUND OF THE SYSTEM page page TROUBLESHOOTING TIPSpage AUTOSOUND 2000 TROUBLESHOOTING TIPS TIME FOR PROCESSORS SUMMATION page AND LOUDSPEAKERS HIGH PERFORMANCE CAR AUDIO AMPLIFIERS, SIGNAL PROCESSORS1998 Orion Industries, Incorporated 9235 S. McKemy St., Tempe, Arizona Phone 602.705.5600 Fax