Owner’s Manual
Programming the Remote Control
Programming the Remote Control
In addition to the RR 2150 itself, the remote control can operate up to three other devices, and is preprogrammed with command codes for hundreds of components.
To program your remote for another device, you will first input a single digit device code, followed by a
nMore than one setup code number may work with a source component. Test the functions for each of the code numbers that work to determine the best one for your particular unit.
nSome components (CD and DVD players, for example) do not have power buttons on their original remote controls and thus may not turn on or off as you expect. If you run into problems, first store the setup code number and then test functions (Play, Stop, etc.) to determine if you’ve selected the correct number.
Setup Using Preprogrammed Codes
To program the remote control using
1.Turn on the device (TV, VCR, cable box) you would like the remote control to operate.
Do this manually or with the device’s original remote control.
2.Find the
The tables of
3.On the RR 2150 remote control, press the proper device selector button (RC2) that corresponds to the device you want to control.
Remember that the RR button is used exclusively for the RR 2150.
4.Press and hold the RR 2150 remote control’s Setup button (RC1).
The red LED at the top of the remote control (RC15) blinks twice.
5.Release the Setup button.
6.Enter the
Press “0” if you are programming a Cable or Satellite box. Press “1” if you are programming a Television.
Press “2” if you are programming a VCR or DVD player. Press “3” if you are programming a CD player.
7.Enter the first
The LED should blink twice. If it does not, repeat the steps above using the same code.
8.Aim the remote control at the component and press the PWR button (RC16) once.
The component should turn off. If it doesn’t respond, repeat steps
If none of the codes work, try searching for the code (see “Searching For Your Code,” below).
9.Repeat the process for other components you wish to control with the RR 2150 remote control.
Searching for Unknown Codes
If your device does not respond to the remote after you have tried all codes listed for your brand, or if your brand is not listed at all, you can try searching for the code.
To search for a code for your component:
1.Press the Device Control Selector button (RC2) on the remote control that corresponds to the device you want to control.
Remember that the RR button is used exclusively for the RR 2150.
2.Press and hold the RR 2150 remote control’s Setup button (RC1).
The red LED at the top of the remote control (RC15) blinks twice.
3.Release the Setup button.
4.Enter 990 using the numeric keys on the remote control (RC3).
The LED will blink twice.
5.To determine the first number in the code sequence, aim the remote control at the component and press 1 on the numeric keypad (RC3) of the RR 2150 remote control.
After three seconds, the LED will blink to indicate that number: i.e., 1 blink = 1, 2 blinks = 2, and so on. Note that no blink indicates the number zero (0).
6.Count the blinks and write down the number.
7.Repeat step for each of the other four digits: Press 2 for the second digit, 3 for the third, 4 for the fourth, and 5 for the fifth.
8.Use the resulting
9.Repeat these steps, but substitute the appropriate device button, for the next component you are checking.
Some General Comments on Using Your Remote
For best remote control performance, please follow these guidelines:
nRemember to point the remote control toward the remote control sensor on the RR 2150, not toward the TV screen.
nPlace the 2150 away from strong light such as direct sunlight or fluorescent light, which can interfere with the infrared pulses generated by the remote control.
nUsing another remote control of a similar type or placing the RR 2150 near equipment which also uses infrared control may cause interference and intermittent operation.
nDo not put anything (other than your hands, of course) on the remote control. If the buttons are continuously pressed by mistake, you’ll probably drain the batteries.
nIf you put your RR 2150 in a closet or behind wood or smoked/colored glass doors, you’ll probably have to mount an infrared sensor outside the cabinet or closet and connect the sensor to the RR 2150’s rear panel IR input (RP2A).
nIf there’s an obstacle between the remote control and the front panel remote control sensor, the remote control will not operate. Remember that IR (infrared) is primarily a “line of sight” control mechanism.
22
Outlaw Audio
