Outlaw Audio RR 2150 owner manual Connecting Your RR, Connecting and Using Antennas

Owner’s Manual

Connecting Your RR 2150

RC13 Tuner Mode button (see page 20)

This button selects either the “FM Stereo” or “FM Mono” tuner mode.

RC14 Memory button (see page 21)

Press this button to begin the process of entering a radio station’s fre- quency into the tuner memory for quick recall.

RC15 Indicator LED (see page 22)

This lights briefly when you push a control key to tell you that the remote has responded to your request. The Indicator LED flashes twice in rapid succession when you’ve successfully entered “setup” mode.

RC16 Power (off button) (see page 18)

Press this button to turn off the RR 2150, or the device currently being controlled by the remote.

NOTE: This is a “Power Off” button only. To turn the RR 2150 on, press any Source Selector button (RC11). This will turn the unit on and select the input you’ve pushed.

RC17 Enter dual function button (see pages 20-21)

RR2150: This button duplicates the functions of the front panel Enter button (FP9). Press it to enter a selection when programming the RR 2150’s tuner functions.

Other components: The function depends on selected component.

RC18 Channel Up/Down dual function buttons (see pages 20-21)

RR2150: When the tuner is in use, press these buttons to go the next higher or lower broadcast frequency

Other components: The function depends on selected component.

RC19 Direct dual function button (see pages 20-21)

RR2150: Pressing this button starts the process of selecting a broadcast station directly. Within five seconds of pressing the button, key in a particular broadcast frequency with the numeric keypad (RC3).

Other components: The function depends on selected component.

RC20 Exit button

This button has no function for the RR 2150. For other components, it will exit an active menu screen, though the function may vary from device to device.

RC21 Function button (see pages 20-21)

RR2150: When the tuner is in use, this button is used to configure the RR 2150’s internal tuner.

Other components: Its function will vary from device to device.

RC22 Menu button

This button has no function for the RR 2150. For other components, it will display a setup menu, though the function may vary from device to device.

RC23 Preset Up and Down buttons (see page 21)

Press this button to scan up and down through the list of radio station frequencies you have programmed into the RR 2150.

RC24 P. Scan button (see page 21)

Press this button to begin a scan of all stations programmed into the RR 2150’s memory system.

Connecting Your RR 2150

Before trying to connect your RR 2150 to other system components, please observe the following simple precautions:

nDon’t connect the power cord to either the AC outlet or your RR 2150 until you’ve made all other connections.

nAlways turn off any device before connecting it to the RR 2150. Better yet, unplug the device from its AC power source, as automatic turn-on signals may inadvertently turn the product on. Better safe than sorry!

nAlways pay attention to the warnings, options, and specific procedures contained in the instructions that came with the component you’re con- necting.

nFor analog connections, remember that

red input jacks = right channel audio white input jacks = left channel audio

nInsert all plugs and connectors securely. If you don’t, you may experience noise, poor performance, or equipment damage.

nDO NOT bundle audio connection cables with power cords and speaker cables. To get the performance you expect, run all the power cords down one side of the cabinet, all the signal connections down the other side, and the speaker cables down the center.

nConnect your speakers after you’ve connected all your other components to the RR 2150 but before you connect the power cord.

Connecting and Using Antennas

The RR 2150 has an internal AM/FM tuner with separate connections for the AM and FM antennae.

FM Antenna

Connect the supplied FM dipole antenna by pushing the antenna’s coaxial connector onto the FM antenna connector (RP2.)

Note: This antenna is for indoor use only. For best reception, fully extend the antenna and experiment with its positioning to get the strongest signal. If FM reception with the supplied indoor antenna does not provide a strong enough signal for acceptable reception, we recommend using an optional amplified indoor or high-gain outdoor antenna.

AM Antenna

Connect the supplied AM antenna to the rear panel push terminals (RP3). Press one lever on the bottom of the terminal block and insert one of the antenna wires. Release the lever and repeat the process with the other wire and lever. Experiment with the antenna's position to obtain the strongest signal.

10

Outlaw Audio