Manuals / Brands / Photography / Camcorder / Panasonic / Photography / Camcorder

Panasonic AG-3DA1E, AG-3DA1P switch, access lamps, Removing SD Memory Cards, Repairing SD Memory Cards, Protecting SD Memory Cards

1 96

Download 96 pages, 8.39 Mb

Removing SD Memory Cards

1 Tilt the viewfinder upwards, and open the SD Memory Card slot cover by sliding the OPEN lever to the right.

•Ensure that the SD Memory Card access lamps are not flashing before opening the cover.

2 Press the center of the SD Memory Card so that it pops out slightly, and pull the card straight outwards.

1

2	SD Memory Card
	access lamps

•Do not remove the SD Memory Card or switch off the power in the following circumstances. Doing so may damage your SD Memory Card.

1)While the SD Memory Card access lamp is still flashing after an SD Memory Card has been inserted.

2)While the SD Memory Card access lamp is flashing such as during recording or during recording finalization.

•It is recommended that you note “Right” or “Left” on the SD Memory Cards. If the left and right SD Memory Cards are inserted in the wrong respective slots, CHECK CARD LEFT/RIGHT is displayed on the viewfinder and LCD monitor.

Protecting SD Memory Cards

Move the write-protect switch on the SD Memory Card to the “LOCK” position to prevent recorded contents being accidentally erased from the card.

Write-protect	LOCK
Write-protect
switch

Repairing SD Memory Cards

	Never remove the SD Memory Card or
	disconnect the battery or DC cable’s battery
	connector while the SD Memory Card access
	lamp is flashing, as doing so may damage the
	SD Memory Card. In the event that the SD
	Memory Card has been removed while the SD
	Memory Card has been removed while the SD	Shooting
	Memory Card access lamp was flashing, or
	that the battery or DC cable’s battery connector
	has been disconnected during recording or
	the recording finalization process, a repair
	verification screen will be displayed the next time
	the power is switched on in order to allow errors
	to be repaired.
	In this case, use the AVCCAM Restorer contents
	repair software to repair the errors.

33

Contents

Page Read this first! (For AG-3DA1P) CAUTION Page Note: Camera-Recorder Battery Charger / AC Adaptor Read this first! (For AG-3DA1E) Read this first! (For AG-3DA1E)(continued) For battery charger FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY FOR CONTINENTAL EUROPE, ETC FOR U.K. ONLY Not to be used in the U.K For AC adaptor EMC NOTICE FOR THE PURCHASER/USER OF THE APPARATUS Applicable standards and operating environment The apparatus is compliant with: 2.Pre-requisiteconditions to achieving compliance with the above standards 3.Performance level Read this first! (For AG-3DA1P/AG-3DA1E) Note concerning illustrations in these instructions References Terminology Overview Contents Read this first Shooting techniques for different How to handle data recorded on SD Operating precautions Liquid crystal displays Do not point the lens or viewfinder at the sun Precaution for use SD Memory Cards compatible with this product Before use Precaution for use (continued) (SD speed class 4) Cautions for usage SDHC Memory Cards Compatibility with equipment other than AG-3DA1(this product) Accessories Optional accessories Description of parts Left side Description of parts (continued) Terminals and mounting parts 1Accessory mounting hole 2Light shoe 3Microphone shoe (Page 66) Charging the battery Power sources Turn on/off the camera Tally lamp Viewfinder Using the LCD 1 Set the POWER/Mode selector switch to ON. (Page 25) 2 Hold down the OPEN button and open the LCD monitor 90° OPEN button Setting the calendar Page Basic shooting operations Basic shooting operation 1 Mode lamp (CAMERA) 2 Adjust the focus, brightness, white balance, and convergence point 3 Press the START/STOP button (Red) to start shooting Checking photos taken (REC CHECK) Basic shooting operations (continued) SD Memory Card access lamps SD Memory Card recording times Illuminated: Flashing (fast): Removing SD Memory Cards access lamps Protecting SD Memory Cards switch Repairing SD Memory Cards Using the zoom function Shooting in progressive mode Adjusting the focus Adjusting the brightness Adjusting the convergence point ■Parallax for pop out ■Parallax in depth Adjusting the white balance Black balance adjustments Shooting techniques for different targets Checking and displaying shooting status DISP/MODE CHK button Using the USER buttons Color bars Shooting techniques for different targets (continued) Wave form monitor function Adjusting the volume while shooting AUDIO MON/ADV buttons Shot mark function 3D FINE function 2 Press the EXEC button 3 Adjust the vertical position of the images, focus and iris finely Vertical position of the images (VERTICAL): Tilt the Operation lever in the Focus (FOCUS): Adjusting the shutter speed When SYSTEM FREQ is set to 50 Hz With the 1080/50i or 720/50P format With the 1080/25P format Synchro scan Switching Audio Input ON: (When using the phantom microphone) OFF: (When a phantom microphone is not connected) INT (L): INPUT 1: INPUT 2: Clip metadata Uploading the metadata (META DATA) Loading the metadata Selecting whether to record the metadata on the SD Memory Cards 1 Press the mode button and select CAMERA mode 3 Tilt the lever in the Clip metadata (continued) Selecting the USER CLIP NAME recording method USER CLIP NAME to be recorded Using the Counter Charging the built-inbattery/Setting the time code 4 When the screen below appears, set the time code value 5 Push the Operation lever when you have finished setting the time code Charging the built-inbattery/Setting the time code (continued) Setting user information 2 In the setup menus, TC/UB SETUP screen, select UB PRESET 4 Set the user information Push the Operation lever when you have finished setting the user information Basic playback operations Thumbnail screen M: Shot mark Playback settings (PLAY SETUP) Thumbnail operations Thumbnail operations (continued) Deleting and protecting clips (OPERATION) DELETE: ALL CLIPS: CLIP PROTECT: Checking clip information (CARD FUNCTIONS) 3 Select YES, and push the Operation lever 1Clip number Thumbnail 3Clip information Useful playback functions Frame-by-frameplayback 1 Tilt the Operation lever in the direction during playback to pause the clip 2 Press the AUDIO MON/ADV buttons AUDIO MON/ADV +/– buttons Adjust volume Connecting external units TV/Monitor Only the output signals from the camera are shown Editing Screen displays 6Information display 7Shutter speed display 8Microphone level automatic control display 9Frame rate display Audio level meter display (Page 49) Screen displays (continued) 20Gain display White balance information display 22Screen mode display R-IMAGE: Main warning displays CANNOT BE USED DUE TO INCOMPATIBLE DATA CANNOT RECORD VIDEO IMAGES ARE PROTECTED. REMOVE PROTECTION YES NO CHECK CARD CLIP NUMBER IS FULL CONTROL DATA ERROR HAS BEEN DETECTED INCOMPATIBLE DATA INCOMPATIBLE CARD THE TC MODE IS CHANGED TO "NDF THIS CARD CANNOT RECORD IN VIDEO MODE THUMBNAIL DATA ERROR IS DETECTED TURN POWER OFF UNABLE TO FORMAT Setting the DISPLAY items MODE CHK OTHER DISPLAY settings Displays (Hold down DISP Using the setup menus Using the setup menus (continued) Repeat steps 4 - 5 to change any other items Repeat steps 2 - 5 to change any other settings Initializing the menu settings Setup menu structure Setup menu list CAMERA SETUP screen (continued) KNEE MID: MATRIX NORM1 Setup menu list (continued) RECORDING SETUP screen REC FORMAT PH 1080/60i PH 1080/30P AV OUT SETUP screen SDI OUT (PB) ON: OFF: DISPLAY SETUP screen (continued) CARD & BATTERY OTHER LCD/EVF OTHER FUNCTIONS screen REC LAMP FRONT: REAR: BOTH: OTHER FUNCTIONS screen (continued) LOG DATA PLAY SETUP screen RESUME PLAY THUMBNAIL SETUP screen Before calling for service Before calling for service (continued) Playback Cannot play even when press the play button Mosaic-likenoise appears Updating the firmware in the camera Cleaning Storage Precautions Recording format How to handle data recorded on SD Memory Card Specifications Thumbnail display Editing functions Formatting [Video System] Video output HDMI output: Index Numerics Page For business users in the European Union Information on Disposal in other Countries outside the European Union Note for the battery symbol (bottom two symbol examples):