NOTE

The same input sources are assigned to the A/PROG bus and the B/PRESET bus.

It is impossible to assign different sources to each bus.

You can check the input source currently assigned to the selected number on the monitor connected to the SDI OUT PVW connector.

To set the video and audio input sources

Video and sound are allocated to input source numbers 1 to 8 on the Audio/Video Input Source Setting screen.

•Allocate the video input sources named [V S-1], [V S-2], [V S-3], and [V S-4] to any of numbers 1 to 8, specifying the video input sources to use.

•Allocate the audio input sources named [A S-1], [A S-2], [A S-3], and [A S-4] to any of numbers 1 to 8, specifying the audio input sources to use.

It is also possible to make settings to establish the correspondence between video input sources and audio input sources. See “To associate video input with audio input” (page 25).

To allocate video and audio to the selected number

Select one of the video input sources [V S-1], [V S-2], [V S-3], and [V S-4] using the rotary 2 control.

Select one of the video [SDI], [HDMI], [VIDEO], and [DVI-I] (SDI input, HDMI input, composite input, and DVI input) as the video input sources [V S-1] to [V S-4] using the rotary 3 control.

Each input type supports the signal formats as shown below.

Input

Format

SDI

All formats

HDMI

720/50p, 720/59p, 1080/50i, 1080/59i,

 

1080/23.98PsF (when [3D]is set to [MODE1] or

 

[MODE2])

VIDEO

480/59i, 576/50i

DVI-I

XGA, WXGA, SXGA, 1080/50p, 1080/60p

Select one of the audio input sources [A S-1], [A S-2], [A S-3], and [A S-4] (SDI input 1 to 4) using the rotary 4 control.

Select one of the audio [SDI], [HDMI], and [ANALOG] (SDI input, HDMI input, and analog input) as the audio input sources [A S-1] to [A S-4] using the rotary 5 control.

NOTE

•If the system format is set to SD (page 19), [HDMI] cannot be selected. If the system format is set to HD, [VIDEO] cannot be selected.

•You cannot set the combinations of video and audio input sources shown in the table below. (The settings are automatically changed to available values.)

When the video input is HDMI, only two channels of audio sources can be input.

Video Input

Audio Input

SDI1

SDI2, SDI3, SDI4, HDMI1, HDMI2

SDI2

SDI1, SDI3, SDI4, HDMI1, HDMI2

SDI3

SDI1, SDI2, SDI4, HDMI1, HDMI2

SDI4

SDI1, SDI2, SDI3, HDMI1, HDMI2

HDMI1

SDI1, SDI2, SDI3, SDI4, HDMI2

HDMI2

SDI1, SDI2, SDI3, SDI4, HDMI1

DVI-I

SDI1, SDI2, SDI3, SDI4, HDMI1, HDMI2

To fix the settings and return to the [AUDIO VIDEO] screen

Press the key.

To return to the [AUDIO VIDEO] screen without fixing the settings, press the key while holding down the SHIFT key.

NOTE

If other menu screen is displayed without fixing of the settings on the Audio/Video Input Source Setting screen, those settings are revoked and not applied.

To associate video input with audio input

1

Set [INPUT] to [V-LINK] using the rotary 2

 

control, and press the

key.

 

 

 

2

When the message [OK?] appears, press the

 

key again.

 

 

 

Audio input sources corresponding to the video

 

input sources assigned to 1 to 8 are set.

 

To cancel the setting, press the

key while

 

holding the SHIFT key.

 

 

The display returns to the [SETUP] menu screen.

NOTE

For input settings in 3D mode, it is possible to select only combinations of image input sources and audio input sources which are associated with each other. When 3D mode is set to other than [OFF], [V-LINK] does not appear as the setting item.

To use the factory default settings

1

Set [INPUT] to [DEFAULT] using the rotary 2

 

control, and press the key.

 

 

2

When the message [OK?] appears, press the

 

key again.

Operation Basic

25