
Setup Mode Operations (continued)
5-1 Save ROP configuration file to memory card
1.Press <SAVE/LOAD> to select [ND].
• Each press of <SAVE/LOAD> toggles between [ND] (Save) and
[CC] (load).
ND CC SHT SYNC
M.GAIN M.PED
IRIS
2.Press <UP> or <DOWN> to select [y] and press <EXECUTE> to confirm the selection.
• Do not remove a memory card that is being accessed.
ND CC SHT SYNC
M.GAIN M.PED
IRIS
•To cancel saving, select [n] and press <EXECUTE>.
•The file is saved to the memory card and [Fin] appears when saving ends.
•[E02] is displayed if the save operation to the memory card fails. (→page 13)
If this happens, check the memory card and try again or insert another memory card to perform the operation again.
•[E01] is displayed when an ROP configuration file with the same name as the one you are attempting to save already exists on the memory card.
To overwrite the file, press <UP> or <DOWN> to select [y] and press <EXECUTE>.(→page 13)
•For details on Save/Load data, refer to page 6.•To exit setup mode, hold down <EXIT> for about 2 seconds.
•To make other settings, press <SELECT> to select a menu number.
5-2 Load ROP configuration file from memory card
1.Press <SAVE/LOAD> to select [CC].
• Each press of <SAVE/LOAD> toggles between [ND] (Save) and
[CC] (load).
ND CC SHT SYNC
M.GAIN M.PED
IRIS
2.Press <UP> or <DOWN> to select [y] and press <EXECUTE> to confirm the selection.
•The file is loaded from the memory card and [Fin] appears when loading ends. A few seconds later, the unit is restarted.
•Do not remove a memory card that is being accessed.ND CC SHT SYNC
M.GAIN M.PED
IRIS
•To cancel loading, select [n] and press <EXECUTE>.
•[E02] is displayed if the load operation from the memory card fails. (→page 13)
If this happens, check the memory card and see whether the file exists on the memory card. If it does, start over from step 1.
•To exit setup mode, hold down <EXIT> for about 2 seconds.
6 Format memory card
1.Press <SELECT>to select menu number [6].Select y (Format)/n (Cancel)
UP | ND | CC | SHT | SYNC | CAMERA | |
| M.GAIN | M.PED | ||||
DATA |
|
|
|
|
| |
SET |
|
|
|
|
| |
|
|
| IRIS |
| No. | |
|
|
|
|
| ||
DOWN | DISPLAY SELECT | SELECT | ||||
SET UP | ND/CC | M.GAIN/M.PED SHUTTER | ||||
| ||||||
SHIFT |
|
|
|
|
| |
+ | SAVE/LOAD |
| EXIT | EXECUTE |
| |
UP+DOWN |
|
| ||||
|
|
| Press to confirm | |||
Press to exit setup mode | Press to select the | |||||
(hold down) |
|
|
| menu number |
2.Press <UP> or <DOWN> to select [y] and press <EXECUTE> to confirm the selection.
•Card formatting starts.•Do not remove a memory card that is being accessed.
ND CC SHT SYNC
M.GAIN M.PED
IRIS
•To cancel formatting, select [n] and press <EXECUTE>.•When the formatting ends, [Fin] appears.•To exit setup mode, hold down <EXIT> for about 2 seconds.
•To make other settings, press <SELECT> to select a menu number.
7 Select/set flare and pedestal
Press <SELECT>to select menu number [7].Select FL (Flare)/PE (Pedestal)
UP | ND | CC | SHT | SYNC | CAMERA | |
| M.GAIN | M.PED | ||||
DATA |
|
|
|
|
| |
SET |
|
|
|
|
| |
|
|
| IRIS |
| No. | |
|
|
|
|
| ||
DOWN | DISPLAY SELECT | SELECT | ||||
SET UP | ND/CC | M.GAIN/M.PED SHUTTER | ||||
| ||||||
SHIFT |
|
|
|
|
| |
+ | SAVE/LOAD |
| EXIT | EXECUTE |
| |
UP+DOWN |
|
| ||||
|
|
| Press to confirm | |||
Press to exit setup mode | Press to select the | |||||
(hold down) |
|
|
| menu number |
7-1 Set flare
Press <UP> or <DOWN> to select [FL] and press <EXECUTE> to confirm the selection.
ND CC SHT SYNC
M.GAIN M.PED
IRIS
•To exit setup mode, hold down <EXIT> for about 2 seconds.
•To make other settings, press <SELECT> to select a menu number.
10