Parts and their functions
GR, G, B gain controls [R, G, B GAIN]
These are used for the red (R), green (G) and blue (B) adjustments of the white balance. When the auto white balance can be performed and the R, G or B gain control is turned, the gain control value on the LCD display changes.
HR, G, B black controls [R, G, B FLARE]
Whether these controls are to be used to adjust the flare or pedestal can be set on the menu. They are used for the red (R), green (G) and blue (B) black adjustments. When the auto black balance can be performed and the R, G or B black control is turned, the flare or pedestal control value on the LCD display changes.
IDTL control [DTL]
This is used to increment or decrement (paint) the detail control settings
By setting this panel’s DTL HD and SD switches, the effect of the DTL control can be applied to the HDTV video output or SDTV video output.
JIris joystick control range selector switch [FULL]
This is used to set the control range of the iris joystick to FULL (when the switch lamp is lighted: from open to close). When the switch lamp is off, the control range of the SENSE control T is used for control.
KAuto iris switch [AUTO]
This is used to activate the auto iris function. Its lamp lights in the auto iris mode.
When the lamp is off, use the Iris/master pedestal control joystick M to control the lens iris.
QP L
MIris/master pedestal control joystick [IRIS/PED]
The iris level of the lens is adjusted by moving the joystick up and down, and the master pedestal is adjusted by turning it.
When in the auto iris mode:
The iris can be adjusted manually.
When not in the auto iris mode: The auto iris level is adjusted.
Since the master pedestal adjustment is independent of the R, G and B pedestal adjustments, the R, G and B pedestal adjustment values remain unchanged even when the master pedestal is changed.
NIris active switch [IRIS ACTIVE]
This makes it possible to adjust the iris. When its lamp is off, the iris cannot be controlled from this panel. If the switch is set to ON and the iris priority is returned to this panel, the panel can then exercise iris control.
OMaster pedestal active switch [M-PED ACTIVE]
This is used to activate the master pedestal control functions of the joystick. Its lamp lights when the functions are activated.
PCall switch [CALL]
This is pressed to call the camera. While it is held down, the lamp of the camera’s call switch lights and the buzzer sounds. After the switch is released, the buzzer stops.
If the call switch on the camera has been pressed, the lamp of this switch remains lighted while that switch is held down.
QAlarm display [ALARM]
This lights when optical transmission is not going satisfactorily or when a problem has occurred in the camera, CCU fan or power supply.
N
O R S V
W
IRIS
ACTIVE ALARM CALL
LENS
X0.8
PED SENSE
IRIS RANGE
PED
IRIS
M
RLens extender display [LENS EXT]
This lights when the setting of the lens extender is other than 1a.
Lighted: The setting of the lens extender is other than 1a.
Off: This indicates that the lens extender is not being used or that the extender function is not available.
SLens ratio effect [a0.8]
This lights when the cross converter is inserted into the lens.
TIris sensitivity control [SENSE]
This is used to adjust the iris control range of the joystick.
U T
LTally indicators
The red tally indicator is at the top and the green tally indicator is at the bottom. They light when the respective tally signals are input to the INCOM/tally connector on the CCU.
UIris control range control [RANGE]
This is used to adjust the iris control position (shift the control range) of the joystick.
VMaster pedestal level indicator
This indicates the master pedestal level in the range of
WIris f-number indicator
This indicates the lens
15
