Panasonic BB-HCM403A 6.3 External I/O

Operating Instructions

151

6.3 External I/O

If you connect external devices such as sensors to the External I/O, and image

buffer/transfer by alarm signal is set, the camera image is transferred by alarm

detection.

Explanation of the External I/O

Note

• The External I/O (Input/Output) are independent. Output terminal is controlled

only by External Output Control page on page 139.

• Do not push strongly on the External I/O with the pointed object. The External

I/O may get stuck into the unit, and you may not be able to use it.

Pin Features

G GND pin

1 Externa l Sensor Input 1

• Use it by opening or GND short-circuit.

G GND pin

2 Externa l Sensor Input 2

• Use it by opening or GND short-circuit.

3 External Device Con trol Output

• You can control this on the External Output page (see page

139).

• It is an open collector circuit, and the maximum drawing-in

current is the same as pin 4. Do not exceed the voltage of DC

power output terminal (pin 4).

4 DC Power Output Terminal

• 10.5—13 V DC

• A maximum of 100 mA load drive is possible.

External I/O Buttons

External I/O

Contents

Main Main Features Dome-shaped Camera for Neat Mounting on the Ceiling PoE (Power over Ethernet) Compliant with a Power Receiving Device Integrated 10x Digital Zoom Feature Motion Detection Feature SD Memory C ard Recording Multi-Camera Page Other Features Abbreviations Trademarks Table of Contents 1 Camera Monitoring....................................................... 8 2 Using the Camera's Basic Features ......................... 35 3 Registering Users....................................................... 75 4 Buffering or Transferring Images.............................. 83 5 Using Other Features............................................... 132 6 Camera Maintenance................................................ 141 7 Other Information ..................................................... 153 8 Index.......................................................................... 182 1 Camera Monitoring 1.1 Feature Locations 1.1.1 Front View Indicator Display 1.1.2 Side View 1.1.3 Bottom View 1.2 How to Turn on the Camera When using the AC Adaptor (Model No. BB-HCA2A: Option) When using a PoE hub (Connecting the AC adaptor is not necessary.) 1.3 Accessing the Camera 1. 2. 3. 4. 5. 1.3.1 To Access the Camera in IPv6 IPv6 Domain Name Service What is IPv6? Setting up the IPv6 Router, your PC, and the Camera Setting up the IPv6 Router 1. 2. 3. Setting up the Camera Confirming that You Can Access the Camera 1.4 Viewing the Single Camera page 2. 3. Page Security Warning window If you cannot install ActiveX Controls or you cannot see the video using the Internet Explorer 1.4.1 Displaying the Banner 1.4.2 Zooming In and Out Clicking the right mouse button (For Only Video) Zoom out Rotating the mouse wheel (For Only Video) Zoom in 1.4.3 Auto Centering the Image (Click to Center) 1. 2. 1.4.4 Tilt Operation Tilt range 1.4.5 Capturing a Still Image 1.4.6 Using the Operation Bar 1.4.7 Setting the Home Position (the administrator only) 1.5 Listening to Camera Audio and Talking through the Camera 2. 3. Talk Button Audio Feature Listen Button Page 1.6 Viewing the Multi-Camera page 2. 3. When an image is not displayed on the Multi-Camera page Using the digital zoom feature on the Multi-Camera page 1.7 Viewing the Buffered Image page 4. Viewer software window Using the digital zoom feature on the Buffered Image page 1.7.1 Deleting Buffered Images 1.8 Viewing Still Images on Your Cell Phone - Page 1.8.1 Enabling or Disabling the Buffer/Transfer on your Cell Phone 2 Using the Camera's Basic Features 2.1 Setup Page of the Camera 2. Page Page 2.2 Connecting the Camera to Your IPv4 Network 1. 2. Most common mode of setup. Uses a static IP address. Uses ISP DHCP server function. 5. Page Page Page 2.3 Connecting the Camera to Your IPv6 Network 1. 2. Most common mode of setup. Uses a static IP address. 5. Page Page 2.4 What is IPsec? Camera's IPsec Features IPsec Mode Selection Page 2.5 Encrypting the Camera Image in Transport Mode 1. 2. 5. 6. Page 2.6 Encrypting the Camera Image in Tunnel Mode 5. 6. 7. 8. 9. 2.7 Using UPnP (Universal Plug and Play) 1. 2. 4. 2.7.1 Connecting the Camera to a Router that Supports UPnP (IPv4 Only) 3. 2.7.2 Connecting the Camera to a Router that Does Not Support UPnP (IPv4 Only) 1. 2. Port Forwarding feature*1 (IPv4 Only) Port Forwarding feature Internet 2.8 Registering with the DynamicDNS Service 1. 2. 3. 4. 5. 6. 7. 8. 2. 4. 5. Page 2.8.1 DynamicDNS Service (IPv4/IPv6) Internet 1. 2. 3. 4. 5. 2.9 Setting the Date and Time 1. Page Page 2.10 Changing Camera Settings Page Page 2.11 Adjusting Audio 1. Page 3 Registering Users 3.1 Changing the Authentication Setting and Administrator User Name and Password IMPORTANT 1. 4. Administrator/General Users/Guest Users 3.2 Logging in to the Camera 3.3 Creating, Modifying or Deleting General Users 1. 2. Note 5. 4 Buffering or Transferring Images 4.1 Procedures of Buffering or Transferring Images 4.2 Buffering or Transferring Images by Timer 2. 3. Page Page Page Page Page Page Page Page 8. 9. 4.3 Buffering or Transferring Images by Alarm Signal 2. 3. Page Page Page Page Page Page Page Page Page 8. 9. An alarm signal is detected. 10. Detectable DetectableUndetectable Page 4.4 Buffering or Transferring Images by Motion Detection Signal 2. 3. Page Page Page Page Page Page Page Page Page 8. 9. A Motion Detection signal is detected. Detectable DetectableUndetectable 10. Page 4.5 Transferring Camera Images in Transport Mode 4.6 Transferring Camera Images in Tunnel Mode 4.7 Setting the Motion Detection Threshold The Threshold is displayed. Only motion above the Threshold is detected. Page 4.8 Setting Alarm Log Notification Page Page 4.9 Using the SD Memory Card Page 4.9.1 Format the SD Memory Card 4.9.2 Start the SD Memory Recording 4.9.3 Stop the SD Memory Recording 2. 3. 4. 5 Using Other Features 5.1 Changing Initial Se ttings on the Single Camera page or the Multi-Camera page 1. Page 4. 5.2 Configuring Multiple Cameras 1. 2. Page 5.3 Specifying Operation Time 1. 2. 3. About Operation Time 5.4 Controlling External Output 1. 2. 3. 5.5 Changing the Indicator Display 1. 2. 4. 6 Camera Maintenance 6.1 Maintenance page Maintenance Page 6.1.3 Confirming Alarm Logs 1. 2. 6.1.4 Restarting the Camera 6.1.5 Updating the Camera Firmware 1. 2. 3. Page 6.1.6 Creating the Configuration File 6.1.7 Loading Settings from a Configuration File 6.1.8 Resetting the Camera to Factory Default 1. 2. 6.2 Support page 6.2.1 The Help page 6.2.2 Product Information 6.2.3 Support Information (1) (2) (3) 6.3 External I/O External I/O Buttons External I/O CAUTION 7 Other Information 7.1 FACTORY DEFAULT RESET Button FACTORY DEFAULT RESET button (Press the button with a pointed object) 7.2 Cleaning 7.3 Setting an IP Address on Your PC 1. 2. 3. Local IP Address 7.4 Using Setup Program Finding the camera 1. 2. Page Automatic Setup (Local or Internet Access) or Manual Setup 1. 2. Page Page Page 7.5 Setting Your PC 7.5.1 Setting Proxy Server Settings on a Web Browser How to Set Proxy Server Settings 1. 2. Page Page 7.5.2 Setting UPnP to Display Camera Shortcut in My Network Places 7.5.3 Setting the Internet Temporary File Setting on the Web Br owser 7.6 Default Setting List Basic Page Page Page Account Buffer/Transfer Page Advanced Page Page 7.7 ASCII Character Table ASCII Character Table 7.8 File Size and Number of Buffered Images The maximum number of Buffer/Transfer images 7.9 Number of Images on the SD Memory Card 7.10 Specifications Page Page Index A B C D U V Z Panasonic Consumer Electronics Company, Division of Panasonic Corporation of North America Panasonic Puerto Rico, Inc. PQQX15560ZA When you ship the product For product service Copyright: