Panasonic BT-LH1760E, BT-LH1760P SYSTEM CONFIG, MENU, MODE, SETUP, STATUS, DISPLAY, Sub menu, Settings, POSITION, POWER ON, BACKLIGHT, INSERTION, CONT./BACK, SUB WINDOW, SETUP LOAD, SETUP SAVE

Main Menu (continued)

SYSTEM CONFIG

			Underlined values indicate factory defaults.
Sub menu	Settings	Description
CONT./BACK.	BACKLIGHT	Selects function to be assigned to [CONTRAST/BACKLIGHT] (front panel
	CONTRAST	knob).
		<BACKLIGHT> Adjusts the BACKLIGHT.
		<CONTRAST> Adjusts the CONTRAST.
BACKLIGHT	0 - 60	Adjusts LCD backlight brightness. Adjust as required by ambient
		conditions.
SUB WINDOW	FULL	Selects sub-window type.
	PART	<FULL> Reduces the entire images for both input signals and places them
		side by side.
		<PART> Cuts out the center of the images for both input signals and places
		them side by side (the images are shown at their original size).
MENU	CENTER	Positions the on-screen menu.
POSITION	LB	<CENTER> Center of the screen
	RB	<LB> Left Bottom	<RB> Right Bottom
	RT
		<RT> Right Top	<LT> Left Top
	LT
STATUS	CONTINUE	Sets display state for input signal status (on-screen menu).
DISPLAY	3SEC OFF	<CONTINUE> Displayed at all times
	OFF	<3SEC OFF> Displayed for 3 seconds after a status change.
		<OFF> Not displayed.
SETUP LOAD	USER5*1*2	Loads saved factory defaults (FACTORY) or user data (USER1 - USER5).
	USER4*1*2	After loading user data, the screen displays the signal selected before
	USER3*1*2	user data was loaded.
	USER2*1*2
	USER1*1*2
	FACTORY
SETUP SAVE	USER5*2	Up to 5 sets of user data can be saved (J page 16).
	USER4*2	They save menu settings and adjustments made with the picture adjusting
	USER3*2	knob (PHASE/CHROMA/BRIGHT/CONTRAST/BACKLIGHT) except
	USER2*2
		“SETUP SAVE/SETUP LOAD.”
	USER1*2
POWER ON	USER5	Selects the settings used when the power is turned on.
SETUP	USER4	<LAST> Starts in the mode used when the power was last turned off.
	USER3	<FACTORY> Starts up using the factory defaults.
	USER2
		<USER1 - 5> Starts up using USER registered settings.
	USER1
	FACTORY
	LAST
COLOR SPACE	SMPTE-C*5	Sets the studio standard color shade.
	EBU*5
	ITU-709*4
POWER SAVE	OFF	Sets the power save mode
MODE	ON	<ON> The backlight dims when no signal (NO SIGNAL) is input for 60
		seconds or longer. Signal input or menu operation will return the
		backlight to its normal brightness.
BLACK DATA	OFF	Doubles the speed of the LCD panel.*3
INSERTION	ON	<ON> Double speed (120 Hz/100 Hz)
		<OFF> Standard speed (60 Hz/50 Hz)

*1 When the monitor is shipped, settings for “USER1” - “USER5” are identical to “FACTORY.”

*2 “H-POSITION”, “V-POSITION”, “PHASE” and “CLOCK” (J page 31) cannot be saved or loaded.

*3 Double speed reduces image lag caused by black signal input but lowers resolution compared to standard speed and some images may generate flicker. Return to standard speed should flicker become noticeable.

*4 ITU-709 is an ITU-R BT.709 standard.

*5 Factory preset settings are The U.S.A. and Canada: SMPTE-C, Others: EBU.

22