REMOTE Specifications (continued)
g Assignment of item priority levels
•When both “MARKER1” and “MARKER2” are ON at the same time, “MARKER1” has priority. However, when the display aspect is 4:3, the “MARKER1” aspect is 16:9, and the “MARKER2” aspect is 4:3, “MARKER2” is displayed. In this case, the “MARKER2” background is controlled.
•When “MARKER BACK HALF” and “MARKER BACK BLACK” are simultaneously activated, priority goes to
“MARKER BACK BLACK”.
•When two or more of the following items - “INPUT SEL. VIDEO”, “INPUT SEL. Y/C”, “INPUT SEL SDI1”, “INPUT SEL. SDI2” and “INPUT SEL. YPBPR/RGB” - are simultaneously activated, priority goes to the last item activated.
•When “GAMMA SEL. FILM” and “GAMMA SEL. STDIO/PST” are simultaneously activated, priority goes to “GAMMA SEL. FILM”.
RS-232C terminal
Refer to the following diagram and lower right table for the
| PC Side |
|
| (Straight) | ||||
|
|
|
|
|
|
|
|
|
| Pin number |
| Signal |
|
|
| Pin number | Signal |
|
|
|
|
|
|
|
|
|
| 1 |
| N.C. |
|
|
| 1 | N.C. |
|
|
|
|
|
|
|
|
|
| 2 |
| RXD |
|
|
| 2 | TXD |
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
3 |
| TXD |
|
|
| 3 | RXD | |
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
| 4 |
| DTR |
|
|
| 4 | DSR |
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
| 5 |
| GND |
|
|
| 5 | GND |
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
| 6 |
| DSR |
|
|
| 6 | DTR |
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
| 7 |
| RTS |
|
|
| 7 | CTS |
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
| 8 |
| CTS |
|
|
| 8 | RTS |
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
| 9 |
| N.C. |
|
|
| 9 | N.C. |
|
|
|
|
|
|
|
|
|
RS-232C REMOTE operation method
g Connectors and signal names Connector: D-SUB 9-pin (female) Signal name
Pin |
| Signal | Explanation | ||
number |
| name |
| ||
|
|
| |||
|
|
|
|
|
|
1 |
| N.C. |
| Not connected | |
|
|
|
|
|
|
2 |
| TXD |
| Transmission data | |
|
|
|
|
|
|
3 |
| RXD |
| Reception data | |
|
|
|
|
|
|
4 |
| DSR |
| Connected inside. | |
|
|
|
|
|
|
5 |
| GND |
| Ground | |
|
|
|
|
|
|
6 |
| DTR |
| Connected inside. | |
|
|
|
|
|
|
7 |
| CTS |
| Connected inside. | |
|
|
|
|
|
|
8 |
| RTS |
| Connected inside. | |
|
|
|
|
|
|
9 |
| N.C. |
| Not connected | |
|
|
|
| ||
g Communication Conditions | |||||
|
|
|
| ||
Signal level |
|
| Conforms to | ||
|
|
| |||
Synchro system |
| Tone pace synchro system | |||
|
|
|
| ||
Transfer rate |
|
| 9600 bps | ||
|
|
|
| ||
Parity |
|
| None | ||
|
|
|
| ||
Data length |
|
| 8 bit | ||
|
|
|
| ||
Stop bit |
|
| 1 bit | ||
|
|
|
| ||
Flow control |
|
| None | ||
|
|
|
|
|
|
g Command format
STX (02h) | Command | : | Data | ETX (03h) |
|
|
|
|
|
•Commands are 3 characters following STX, finally adding ETX.
•Add a : (colon) after the command as required, and add the data.
g Response formats |
| |||
1. | Setting command response |
| ||
|
|
|
|
|
| STX (02h) | Command |
| ETX (03h) |
|
|
|
|
|
2. | Query command response |
| ||
|
|
|
| |
| STX (02h) | Data |
| ETX (03h) |
|
|
|
|
|
3. | Error response |
| ||
|
|
|
| |
| STX (02h) | Error code |
| ETX (03h) |
|
|
|
|
|
| Error code |
|
|
|
ER001: Invalid command
ER002: Parameter error
31