Panasonic CF-T2 Series Replacing the Battery Pack

43

Battery Power

2Close all the application.

3Use the "Battery Recalibration" to fully discharge the battery pack.

ARun the Setup Utility. (Îpage 79)

BSelect [Battery Recalibration] from [Exit] menu and press

Enter

.

CAt the confirmation message, select [Yes] and press

Enter

.

Once the battery indicator turns green, the battery pack will be completely dis-

charged. It takes approximately 3 hours until the power automatically goes off

through the complete discharge of the battery from the fully charged state.

4Allow the battery pack to charge until the battery indicator turns

green.

Charging Time: Approximately 3 hours.

The battery pack is a consumable item and therefore will require replacement (CF-

VZSU24U/CF-VZSU24AU). If the battery operation time becomes noticeably short, and if

performance is not recovered even after executing Battery Recalibration, we recommend that

the battery be replaced.

CAUTION

zDo not touch the terminals on the battery pack and the computer. The batter y pack

may no longer function properly if the contacts are dirty or damaged. Also, the

computer may not operate properly.

zThe battery pack is not charged when it is first purchased. Be sure to charge it before

using it for the first time. When the AC adaptor is connected to the computer,

charging begins automatically.

zUse only the specified battery pack (CF-VZSU24U/CF-VZSU24AU) with your

computer.

zIn the standby mode, do not remove/change the battery pack. Removing the pack in

the standby mode will erase your data and may damage the computer.

Replacing the Battery Pack

Contents

Main Read Me First Illustrations and Terminology in this Reference Manual Read Me First About Display Mode Key Combinations Page Page Page Hotkey Settings 1 2 Page LED Indicators LED Indicators Touch Pad Using the Touch Pad Utility How to Scroll 1 2 3 4 without removing your finger from the pad. 5 Hints for Easier Touch Pad Operation Page 8 Adjusting the Sensitivity when Touching the Touch Pad 9 1 2 3 Handling the Touch Pad Touch Sensitivity Touchscreen To right-click: Page Configuring the Touchscreen 1 2 Handling the Touchscreen Handling the Stylus Standby/Hibernation Functions Differences between the Standby and Hibernation Functions Entering the Standby or Hibernation Mode Starting Up Your Computer Quickly Setting for Using the Hibernation Mode 1 [Power Options]. 2 [OK]. Precautions Before entering the standby or hibernation mode 1 [Power Options] - [Advanced]. 2 Entering the standby or hibernation mode 1 Using the Display Setting 1 [Power Options] - [Advanced]. 2 portable computer], and then select [OK]. Entering the standby or hibernation mode Resuming Operation Using the Power Switch 1 Security Measures 3 Setting the Supervisor Password (enabling, changing, disabling) 4 5 8 7 6 Setting the User Password (enabling, changing, disabling) 3 4 8 7 When you do not want your computer to be used without permission 4 and select [Yes], then press 5 Starting Up When the Password on boot is Set When you do not want the data on the hard disk to be read/ written Setting the Hard Disk Lock (enabling, disabling) 3 4 5 Computing on the Road Saving Power Power Saving Methods Computing on the Road To Avoid Problems When Remaining Battery Power Is Low Battery Power Use the Battery Indicator to Check the Battery Status Check the Remaining Battery Power Page Page When the Remaining Battery Charge Becomes Low Accurately Displaying Battery Capacity (Battery Recalibration) 1 2 3 Replacing the Battery Pack 4 green. Page SD-MovieStage 1 Running the SD-MovieStage 1 Setting Up the SD-MovieStage PC Cards PC Cards Inserting/Removing the PC Card Inserting a PC Card 1 Removing a PC Card PC Cards SD Memory Card/MultiMedia Card SD Memory Card Formats for SD memory cards Data transfer rate Important handling and storage information SD Memory Card/MultiMedia Card When logging on to Windows/ resuming from standby or hibernation mode Protecting important data MultiMedia Card (MMC) Page SD Memory Card/MultiMedia Card Removing the Card SD Memory Card Drive Letter 1 2 Page SD Memory Card Security Function Before Initialization (SD Card Setup) Initialization (SD Card Setup) 1 2 3 4 5 6 In the Function fails to Operate Correctly When resuming from the standby or hibernation mode, or while the screensaver is active Change the Settings 1 2 Page 4 External Display 1 2 3 4 Extended Desktop 1 2 and [Secondary Device]. Page Page USB Devices Connecting/Removing USB devices Connecting USB devices 1 referring to the operating instructions of the USB device. USB Devices Removing USB devices 1 2 USB Floppy Disk Drive Page Modem Connecting the Internal Modem with a Telephone Jack 1 2 Modem Ring Resume Function Enabling the Ring Resume Function Modem LAN Connecting LAN 1 2 3 LAN Wake up from LAN Enabling the Wake up from LAN Function LAN Wireless LAN Precautions The Settings 1 2 3 4 5 6 7 Check the Communication Status 8 If the function fails to operate correctly The access point fails to be displayed in [Available Networks] The access point cannot be accessed The IP address of the access point is wrong Setup Utility Running the Setup Utility 1 2 while [Panasonic] boot screen is displayed soon after the computer begins the startup procedure. Key Operations Information Menu Main Menu Advanced Menu Security Menu Page Boot Menu Exit Menu Icon Enlarger How to Magnify the Computer Screen Display 1 2 Size]. Technical Information Network Connections and Communications Software When Using the Files on the Retail Version of the Windows CD-ROM DMI Viewer 1 2 Running DMI Viewer Saving information to a file List of Error Codes List of Error Codes Dealing with Problems (Advanced) Page Enter Password Page Setup Utility Shutting Down Standby/Hibernation Function Battery Indicator Keyboa rd Network Page Disk Operations Tou ch Pad Disk Operations Touchscreen Sound SD Card Setup (SD memory card security function) Fast User Switching Function Others Check the Computer's Usage Status Running PC Information Viewer Save information to a file Save a copy of the screen to a file