Battery
The battery indicator is | z | The battery level is very low (the charge is approx. 9% or less). |
|
| |||||||||
lights red | z | Connect the AC adaptor. You can use the computer when the indicator light is orange. If |
|
| |||||||||
|
|
| you do not have an AC adaptor, save your data and power off your computer. After |
|
| ||||||||
|
|
| replacing the battery pack with a fully charged one, turn your computer on again. |
|
| ||||||||
The battery indicator is | z | If blinking red: |
|
| |||||||||
blinking |
| Quickly save your data and power off your computer. Remove the battery pack and dis- |
|
| |||||||||
|
|
| connect the AC adaptor, then connect them again. If the problem persists, contact your |
|
| ||||||||
|
|
| technical support office. The battery pack or charging circuit may be defective. |
|
| ||||||||
|
| z | If blinking orange: |
|
| ||||||||
|
|
| • | Battery cannot be recharged temporarily because the internal temperature of the bat- |
|
| |||||||
|
|
|
| tery pack is outside the acceptable temperature range for recharging. Your computer |
|
| |||||||
|
|
|
| can be used normally in this state. Once the range requirement is satisfied, charging |
|
| |||||||
|
|
| • | begins automatically. |
|
| |||||||
|
|
| Software applications and peripheral devices (USB devices, etc.) are consuming too |
|
| ||||||||
flashing |
|
| much power. Exit the software applications currently running. Once the range require- |
| Started | ||||||||
| If [Battery Charging Indicator] in [Main] menu of the Setup Utility is set to [Flashing], |
| |||||||||||
|
|
|
| ment is satisfied, charging begins automatically. |
|
| |||||||
The battery indicator is | z The battery is recharging. |
|
| ||||||||||
|
|
| the indicator will alternately become lighter and darker. |
| Getting | ||||||||
The cursor does not work. | z | When using the external mouse, connect it correctly. |
| ||||||||||
| Touch Pad |
|
|
|
|
|
|
|
|
|
|
|
|
|
| z | Restart the computer using the keyboard. |
|
| ||||||||
|
|
| (Press |
|
| , |
| , and |
| to select [Restart].) |
|
| |
|
|
|
| U | R |
| Information | ||||||
|
| z If the computer does not respond to keyboard commands, read “No response” (Î page 28). |
| ||||||||||
|
|
|
| ||||||||||
Cannot input using the | z | Set [Touch Pad] to [Enable] in the [Main] menu of the Setup Utility. |
|
| |||||||||
touch pad. | z | The drivers for some mice may disable the touch pad. Check your mouse’s operating instructions. |
|
| |||||||||
| Recover Pro |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Useful | |||||||
Cannot install Recover Pro | z | Recover Pro cannot be installed when four primary partitions exist. Reduce the number |
| ||||||||||
|
|
| of primary partitions to three or less before installation. You can check the number of the |
| |||||||||
|
|
|
|
| |||||||||
|
|
| primary partitions in the order of [start] - [Control Panel] - [Performance and Mainte- |
|
| ||||||||
|
|
| nance] - [Administrative Tools] - [Computer Management] - [Disk Management]. |
|
| ||||||||
|
| z | Recover Pro cannot be installed when a backup area is remaining on the hard disk. Try |
|
| ||||||||
|
|
| one of the following methods: |
| Troubleshooting | ||||||||
|
|
| • | include complete backup data: |
| ||||||||
|
|
| If the backup area has complete backup data and you want to restore that data: |
|
| ||||||||
|
|
|
| Follow the “Complete Restore” instructions in “Hard Disk Backup Function (Recover |
|
| |||||||
|
|
|
| Pro)” (Î page 21) to restore the data. |
|
| |||||||
|
|
| • | To return the computer to its condition at the time of shipment: |
|
| |||||||
|
|
|
| Reinstall the software (Î page 23). |
|
| |||||||
|
|
|
| • In step 8, do not select “3. Reinstall Windows to the first partition.” |
|
| |||||||
|
|
| • | If you do not need the data in the backup area, or if it is corrupted, or if does not |
|
| |||||||
|
|
| A Access [http://www.phoenix.com/en/Customer+Services/Utilities/ |
|
| ||||||||
|
|
|
| ||||||||||
|
|
|
| Recover+Pro+6.htm#Where], and download/install “Cleanup Utility for Recover Pro 6”. |
|
| |||||||
|
|
| B Delete the backup area using “Cleanup Utility for Recover Pro 6”. |
|
| ||||||||
|
|
| In this case, all data in the backup area will be lost. |
| Appendix | ||||||||
An unnecessary backup |
| A Access [http://www.phoenix.com/en/Customer+Services/Utilities/ |
| ||||||||||
|
|
| |||||||||||
area is present (is left) when |
|
| Recover+Pro+6.htm#Where], and download/install “Cleanup Utility for Recover Pro 6”. |
|
| ||||||||
Recover Pro is not installed. |
| B Delete the backup area using “Cleanup Utility for Recover Pro 6”. |
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Reference Manual
The Reference Manual is not | z Install Adobe Reader. |
displayed. | A Log on to Windows as an administrator. |
| B Click [start] - [Run], input [c:\util\reader\AdbeRdr70_enu_full.exe], then click [OK]. |
| Follow the |
| C Update Adobe Reader to its latest version |
| If your computer is connected to the internet, start up Adobe Reader and click [Help] - |
| [Check for updates now] |
|
|
27