Panasonic CQ-C5405U, CQ-C5305U warranty Preparation, General

Preparation

		The demonstration message appears for initial use.							Turn [VOL] counterclockwise.
		1 Set your car’s ignition switch to the
									5 For using the remote control, press [0] ().
Cancellationof	Demonstration		ACC or ON position.
		4 Press [VOL] (PUSH SEL: Select) to
									23)	.
		2 Press [PWR] (Power).
		3 Hold down [VOL] (PUSH SEL: Select)							Notes:
			for 2 sec. or more to open the menu.						• To return to the regular mode, press [DISP].
									• Refer to the section on “Function Setting” ( page
			select the Demonstration setting.						• When “NO DISC” is displayed, the Demonstration
			(“DEMO” is displayed)						cannot be cancelled.
			Preparation Before Initial Use							Warning
			Pull the insulation film
									Keep batteries and insulation film out of reach of
			out from the backside of
									infants. If an infant ingests a battery, please seek
			remote control gently.
									immediate medical attention.
Preparation
					Insulation film					Cautions
									• Remove and dispose of an old battery immediately.
			Battery Replacement
									• Do not disassemble, heat or short a battery. Do not
			Remove the battery				Tough pointed object		throw a battery into a fire or water.
			holder with the remote						• Follow local regulations when disposing of a
Control			control unit placed on a						battery.
			flat surface.						• Improper use of a battery may cause overheating,
			 Stick your thumbnail						an explosion or ignition, resulting in injury or a fire.
				into the groove, and
Remote				push the holder in					Notice
				the direction of the
									This product contains a CR Coin Cell Lithium
				arrow, and at the
									Battery which contains Perchlorate Material - special
				same time.		Back side
									handling may apply.
			 Pull it out in the
									See www.dtsc.ca.gov/hazardouswaste/perchlorate.
				direction of the
				arrow using a tough					Note: Battery Information:
				pointed object.
			 Put a battery in the case						Battery Type: Panasonic lithium battery (CR2025)
										(Included in the remote control)
			with () side facing up.				
									Battery Life: Approximately 6 months under normal use
			 Put the case back.
										(at room temperature)
Adjustment		The 12-hour system is used for the clock.
		1 Press [PWR] (Power).							Adjust the minute and press [DISP] to
									5 confi rm the adjustment.
		2 Press [DISP].							[]: Forward
		3 Hold down [DISP] for 2 sec. or more.							[]: Backward
									Notes:
Clock		4 Adjust the hour and press [DISP].							• Adjust the clock when “ADJUST” appears on the display.
									• Hold down [] or [] to change numbers
			[]: Forward
									rapidly.
			[]: Backward
									• When “NO DISC” is displayed, the clock cannot be
									adjusted.

General
This chapter explains how to turn on or off the power, how to adjust the volume, etc.
On/offPower	Power)(PWR:	Power On	English
		Press [PWR] (Power).
		Power Off
		Hold down [PWR] (Power) for 1 sec. or
		more.

You can remove the face plate to prevent it from being stolen.

	Removing	Mounting	General
Removing/MountingPlate System)Theft-(Anti			Preparation,
	1 Turn off the power. ( above)	1 Fit the face plate with its left hole on the
	2 Press [OPEN]. The face plate will be	left pin provided on the main unit.
		2 Fit the other hole on the other pin
	opened.
	3 Push the face plate to the	applying slight pressure.
	left.
	4 Pull it out toward you.
	5 Put the face plate in
Face	the case.
	Cautions	• Do not touch the contacts on the face plate or on
		the main unit, since this may result in poor electrical
	• This face plate is not waterproof. Do not expose it to	contacts.
	water or excessive moisture.
		• If dirt or other foreign substances get on the
	• Do not remove the face plate while driving your car.
		contacts, wipe them off with clean and dry cloth.
	• Do not place the face plate on the dashboard or
		• To avoid damaging the face plate, do not push it
	nearby areas where the temperature rises to high.
		down or place objects on it while it is open.

		The display changes as follows every time [DISP] is	At Power-on:
ChangeDisplay		pressed.	When the power is set to ON, refer to the description for
	Display)(DISP:	At Power-off:	each source mode.
		Clock display (Default)
		Display Off

10 CQ-C5405U/C5305U CQ-C5405U/C5305U 11