Panasonic CQ-C9901W, C9801W operating instructions Radio

Radio

		You can assign your favorite broadcasting station to the
		[D·M] button. As the result of doing that, your favorite
		broadcasting station can be received even if the CD mode	SRCCS
		or the CD changer mode is activated.
		(Default: FM 87.50 MHz)
		Note: For the use of an FM transmitter, it is useful
		for users to register applicable frequencies on D·M
MemoryDirect	MEMORY)DIRECTM:(D·	(Direct Memory).
		D·M station calling
		1 Press [D·M: DIRECT MEMORY].
		D·M station writing
		1 Select a station you would like to preset.
		2 Hold down [D·M: DIRECT MEMORY]	Lights when the D·M mode is activated.
		for 2 sec. or more.

	Up to 6 stations can be preset in AM, FM1, FM2, and FM3	Manual station preset
	respectively.
		1 Tune in to a station.
	Preset stations can be simply called up by pressing [}]
	(P·SET) or [{] (P·SET).	2 Hold down [}] or [{] for 2 sec. or
	Notes:
	¡ Direct Access can be executed with [1] to [6] buttons		more.
	on remote control.	3 Select a preset number by pressing [}]
PRESET)	¡ You can switch between 6 and 18 for FM presetting
	stations. (a page 21)
			or [{].
	¡ Preset stations are changeable. (a page 21)
		4 Preset the station by holding down [}]
PresetStation P·SET:MEMORY,PRESETAUTO	Auto Preset Memory (APM)
			or [{] for 2 sec. or more.
	Stations with good receiving conditions are automatically
	preset.
	1 Select a band.
	2 Hold down [BAND]
			Frequency/preset number blinks once.
	(APM) for 2 sec.	Notes:
	or more.
		¡ New stations overwrite existing saved stations.
		¡ In step 2, a station can be registered by holding down
(APM:	The preset stations under best receiving conditions	the numeric button [1] to [6] for 2 sec. or more.
	are received for 5 sec. each after presetting the sta-	¡ To stop presetting stations, press [DISP] (Display).
	tions (SCAN). To stop scanning, press [}] or [{].

Note: New stations overwrite existing saved stations.

Mono/Local Setting (Radio Menu Display)

(MONO/LOCAL)

In the AM mode, only NOISE SUPPRESSION and LOCAL can be selected.

1 Press [MENU] to

display the menu display.

For using the remote control, hold down [MENU] for 2 sec. or more.

2 Press [}] or [{] to select a mode to be adjusted.

3 Press [BAND]

(SET) to adjust.

4 Press [MENU] to confirm the adjust- ment.

For using the remote control, hold down [MENU] for 2 sec. or more.

MONO (Monaural)

Noise reduction when the signal strength decreases

: Receiving in stereo (default)

: Receiving in mono and reducing the noise level

LOCAL

Setting when searching for a station

: Searching even for a relatively low-intensity radio wave station (default)

: Searching only for a high-intensity radio wave station

NOISE SUPPRESSION

IF filter setting for noise suppression

: Wide range

: Middle range (default) : Narrow range

AUTO PRESET

You can select 6 or 18 stations for FM presetting with the	English
use of APM.
:
Presets 6 stations to FM1 to FM3 respectively, that is, 18
stations in total at the same time. This function is useful
for presetting more than 6 stations. (default)
:
Presets 6 stations with good reception to the selected
band from FM1 to FM3. This function is useful for preset-
ting stations in different areas in different bands.
PRESET EDIT
You can arrange the order of the preset stations. Preset
stations can be reordered as you like after executing APM
or the like.
1 Press [}], [{], []] or [[] to select one
station to be interchanged.
2 Press [BAND] to confirm your selection.
3 Press [}], [{], []] or [[] to select the
	Radio
other station to be interchanged.
4 Press [BAND] to confirm your selection.
●Calling an FM station registered on D·M
RADIO AUDIO FILTER
You can select the reception status (band) of FM stations
registered on D·M.
: Off (default)
: High cut level 1
: High cut level 2 (same processing at receiving
an FM station)

20 CQ-C9901W/C9801W CQ-C9901W/C9801W 21