10 CQ-C9901W/C9801W 11
English
CQ-C9901W/C9801W
Preparation
Note:Adjust the clock when “ADJUST” appears on the
display.
1Press [MENU] to display the menu dis-
play.
For using the remote control, hold down [MENU]
for 2 sec. or more.
2Press []]or [[]to display the DIS-
PLAY menu.
3Press [{]to select “CLOCK ADJ”.
4Press [BAND] (SET) to confirm the dis-
play.
5Adjust the setting value.
[[]
:
Adjusting minutes
[]]
:
Adjusting hours
[}]
:
Forward
[{]
:
Backward
6Press [BAND] (SET) to confirm the
adjustment.
Note:For cancellation of clock adjustment, press
[DISP].
7Press [MENU].
For using the remote control, hold down [MENU]
for 2 sec. or more.
When the power is switched on for the first time, a
demonstration message appears on the display. Press
[DISP]to change to regular mode.
1Set your car’s ignition switch to the ACC
or ON position.
The demonstration screen appears.
Example:CQ-C9901W
2Press [DISP: DISPLAY].
The demonstration screen is cancelled, and no more
appears. Note:If you would like to turn on the power and make
the demonstration message appear, hold down [SRC]
(PWR: POWER) for 4 sec. or more.
You may need to set the following depending on the
devices to be connected.
Using Subwoofer
¡Subwoofer level adjustment (apage 32)
¡Subwoofer low pass filter (apage 32)
Connecting an AV device (TV, VTR)
If you connect TV to AUX1 terminal, set the AUX1 setting
to TV.
1Press [SRC: SOURCE] to select the
AUX1 mode. (apage 14)
2Press [MENU] to display the menu dis-
play.
For using the remote control, hold down [MENU]
for 2 sec. or more.
3Press [BAND] (SET)to adjust.
: TV
: Other devices (Default)
Note:When using an external TV unit manufactured by
a third party, select the TVmode.
4Press [MENU] to confirm the adjust-
ment.
The following functions are activated when the Security
Function is ON. (apage 34)
¡The security indicator blinks when removing the face
plate.
¡The alarm sounds and the message appears on the
screen to warn you to remove the face plate at power
off.
Security Indicator
SRC CS

Preparation

First Time Power On

(DEMONSTRATION)

Remote Control PreparationSecurity Function

Setting

Other SettingsClock adjustment

(CLOCK ADJ: CLOCK ADJUSTMENT)
Battery Replacement
Preparation Before Initial Use
Pull the insulation film out
from the backside of
remote control gently.
Warning¡Keep batteries and insulation film out of reachof infants. If an infant ingests a battery, pleaseseek immediate medical attention.Caution
¡Remove and dispose of an old battery immediately.
¡Do not disassemble, heat or short a battery.Do not throw a battery into a fire or water.¡Follow local regulations when disposing of abattery.¡Improper use of a battery may cause overheat-ing, an explosion or ignition, resulting in injuryor a fire.
Note:
¡Battery Information:Battery Type: Panasonic lithium battery (CR2025)(Included in the remote control)Battery Life: Approximately 6 months under nor-mal use (at room temperature)
q
w
qRemove the battery holder
with the remote control unit
placed on a flat surface.
qStick your thumbnail into
the groove, and push the
holder in the direction of
the arrow, and at the
same time.
wPull it out in the direction
of the arrow using a
tough pointed object.
wPut a battery in the case with
(+)-side facing up.
ePut the case back.
23
Tough pointed object
Back side
Insulation film