Job Memory, To Store a Job in Memory | Panasonic DP-1510P specification

Creative Features

Job Memory

■Two Copy Jobs Can Be Programmed in Memory (M1, M2) for recall at a later time.

JOB MEMORY

PRESS M1,M2 TO STORE.

To Store a Job in Memory

#Set up the copy job to be stored in memory, by first selecting each function you wish the copier to perform.

$Press the MEMORY IN (F2) key.

%Press the M1 (F3) or M2 (F4) key.

RECALL JOB MEMORY

To Recall a Job Stored in Memory

&Place the Original

(Press the M1 (F3) or M2 (F4) key. The stored contents will be displayed.

)Press START

	NOTE	CStored job(s) will not be deleted even if the power switch is turned Off.
	NOTE	CWhen storing a new job into programmed memory, the previously stored job will be

		overwritten.

Page 22

Image 22

Panasonic DP-1510P Job Memory, To Store a Job in Memory, To Recall a Job Stored in Memory, $Press the Memory in F2 key

Contents

Options Before StartingEnglish Others Important Information Model and Serial Number Operation Chart Common Features and Usage Energy Star Table of Contents Options Problem SolvingOthers For Your Safety PrecautionsLaser Safety Handling Toner and Paper Ventilation Installation For U.K Control Panel Interrupt Key, Memory in Key, M1/M2 Keys Contents Refer to Stop KeyLCD Display Copy Size Key Copying the Same Size Originals Basic CopyFull Size Copying $Select Exposure Control Select the Copy Copying with Preset RatiosReduction or Enlargement Copying Paper Tray key Press Cursor G or F keys to select Zoom Ratio Zoom CopyingZoom Select Original Copying on Special Paper, etc Using the Sheet Bypass$Adjust the side guides Press Start 1 Copy Creative FeaturesProcedure Press Copy Place the Press Originals page Copy KeyPlaten Press BOOK, Edge Or Margin key Key Operation Sided/1-Sided Copy For DP-2010EBook \ Press 2-Sided \ 2 / 2 \1 / 2 \ 2 Copy For DP-2010ESided Copy key Book \ 2 Copy For DP-2010E Place the Original on the Platen To Recall a Job Stored in Memory Job MemoryTo Store a Job in Memory $Press the Memory in F2 key Sort Copy Sort ModeSort Copy From Platen Glass only Energy Saver Mode Other FeaturesEnergy Saver/Interrupt Mode Sleep Mode Skyshot Mode Digital Skyshot Mode Manual Skyshot Mode Platen Upper- left corner Next Combined Function TableRemarks Job Memory Retrieval Using Function Modes to Change the Initial Copy Modes Function Modes Function Initial Setting General Functions Copier Settings General Functions for Key Operator Copier Settings for Key Operator Press the Function key Function SettingChanging the Auto Exposure Setting Proceed as Follows Changing the Paper Size Function Setting for Key OperatorFunctions Stopper Guide a Paper Guide b IndicatorPaper Size Department Counter Select the Department Counter Mode Page Accessories Components ADF DA-AS180 / i-ADF DA-AR201 FeaturesAutomatic Document Feeder Components Original OperationPlace Inappropriate Originals Adding Paper J Problem SolvingSheet Paper Tray Remove the Waste Toner Container by Adding the Toner and Replacing Waste Toner Container ?Open the Front Cover Slowly pulling it towards the left as Problem Solving Removing a Misfed Paper Paper Misfeed Locations Paper Exit Area Remove the misfed paper Hot Paper Entry/Transport AreaOpen the Right Cover Remove the misfed paper Heated Open the Right Cover ADU Area For DP-2010E onlyClose the Right Cover Paper Feed Module ADF For DP-2010E only ADF Check Action TroubleshootingBefore Calling Service Unit Does Not Operate Light Copies Add Toner Warning IndicatorMarked Copies User Error Codes U Code As a rule, clean weekly Specifications DP-1510P/1810P/2010E Copier 2nd/4th Paper Feed Module DA-DS182 ADF DA-AS180ADF DA-AR201 3rd Paper Feed Module DA-DS183 For Network Printing Options and SuppliesFor Printer SuppliesPage Page For Service, Call

Panasonic DP-1510P manual Job Memory, To Store a Job in Memory, To Recall a Job Stored in Memory

Models: DP-1510P

Job Memory

To Store a Job in Memory

$Press the MEMORY IN (F2) key.

To Recall a Job Stored in Memory