Function Setting for Key Operator, Functions

Function

Function Setting for Key Operator

■Changing the Paper Size

The Paper Trays are designed to accommodate A5, A4, A4 R, FLS/B4 and A3 size paper. To change the paper size, perform the steps shown below.

1	Press the FUNCTION key.	FUNCTION Key

2	Proceed as Follows:

			FUNCTION MODE (1-2)
			ENTER NO. OR ∨ ∧

	#Press the 1 key to select GENERAL
		FUNCTIONS.

			1:GENERAL FUNCTIONS
			PRESS SET TO SELECT

	$Press the SET key.

			GENERAL PARAM. (0-9)
			ENTER NO._ OR ∨ ∧

	%Press 9 key.

			09 KEY OPERATOR MODE
			ENTER PASSWORD=- ■ ■

&Input the Key Operator ID code (3 digit) and the SET key.

KEY OPR. MODE (00-25)

ENTER NO._ OR ∨ ∧

(Press 00 and 1 or 2 key to select the PAPER SIZE.

00 PAPER SIZE 1:TRAY-1[A3i]

)Press SET to select the paper tray and press (G or F) keys to set the paper size.

Paper size changes are as follows.

A3 B4 A4

A4RFLS1FLS2 A5B5B5R

*Press the SET key to set up the PAPER SIZE.

+Press the RESET key to exit the Function mode.

Page 34

Image 34

Panasonic DP-1510P manual Function Setting for Key Operator, Changing the Paper Size, Functions

Contents

Options Before StartingEnglish Others Important Information Model and Serial Number Operation Chart Common Features and Usage Energy Star Table of Contents Options Problem SolvingOthers For Your Safety PrecautionsLaser Safety Handling Toner and Paper Ventilation Installation For U.K Control Panel Interrupt Key, Memory in Key, M1/M2 Keys Contents Refer to Stop KeyLCD Display Copy Size Key Copying the Same Size Originals Basic CopyFull Size Copying $Select Exposure Control Select the Copy Copying with Preset RatiosReduction or Enlargement Copying Paper Tray key Press Cursor G or F keys to select Zoom Ratio Zoom CopyingZoom Select Original Copying on Special Paper, etc Using the Sheet Bypass$Adjust the side guides Press Start 1 Copy Creative FeaturesProcedure Press Copy Place the Press Originals page Copy KeyPlaten Press BOOK, Edge Or Margin key Key Operation Sided/1-Sided Copy For DP-2010EBook \ Press 2-Sided \ 2 / 2 \1 / 2 \ 2 Copy For DP-2010ESided Copy key Book \ 2 Copy For DP-2010E Place the Original on the Platen To Recall a Job Stored in Memory Job MemoryTo Store a Job in Memory $Press the Memory in F2 key Sort Copy Sort ModeSort Copy From Platen Glass only Energy Saver Mode Other FeaturesEnergy Saver/Interrupt Mode Sleep Mode Skyshot Mode Digital Skyshot Mode Manual Skyshot Mode Platen Upper- left corner Next Combined Function TableRemarks Job Memory Retrieval Using Function Modes to Change the Initial Copy Modes Function Modes Function Initial Setting General Functions Copier Settings General Functions for Key Operator Copier Settings for Key Operator Press the Function key Function SettingChanging the Auto Exposure Setting Proceed as Follows Changing the Paper Size Function Setting for Key OperatorFunctions Stopper Guide a Paper Guide b IndicatorPaper Size Department Counter Select the Department Counter Mode Page Accessories Components ADF DA-AS180 / i-ADF DA-AR201 FeaturesAutomatic Document Feeder Components Original OperationPlace Inappropriate Originals Adding Paper J Problem SolvingSheet Paper Tray Remove the Waste Toner Container by Adding the Toner and Replacing Waste Toner Container ?Open the Front Cover Slowly pulling it towards the left as Problem Solving Removing a Misfed Paper Paper Misfeed Locations Paper Exit Area Remove the misfed paper Hot Paper Entry/Transport AreaOpen the Right Cover Remove the misfed paper Heated Open the Right Cover ADU Area For DP-2010E onlyClose the Right Cover Paper Feed Module ADF For DP-2010E only ADF Check Action TroubleshootingBefore Calling Service Unit Does Not Operate Light Copies Add Toner Warning IndicatorMarked Copies User Error Codes U Code As a rule, clean weekly Specifications DP-1510P/1810P/2010E Copier 2nd/4th Paper Feed Module DA-DS182 ADF DA-AS180ADF DA-AR201 3rd Paper Feed Module DA-DS183 For Network Printing Options and SuppliesFor Printer SuppliesPage Page For Service, Call

Function Setting for Key Operator

■Changing the Paper Size

Press the FUNCTION key.

Proceed as Follows:

FUNCTIONS.