Before Requesting Help | Panasonic KX-TC1851ALB, KX-TC1851NZB

ÒBefore Requesting Help

Problem

Cause and Remedy

The handset display is still ³Charge the battery fully (p. 11). blank after pressing (Ý),

(Ü), BACK (Þ) or FWD/EDIT

(ß).

You cannot program items, ³Programming is not possible while the

such as the dialling mode. unit is in the talk mode or when viewing the Caller List/directory list.

³Do not pause for over 60 seconds while programming.

³Move closer to the base unit.

³(Ý), (Ü), BACK (Þ) or FWD/EDIT (ß) may have been pressed when you picked up the handset. Press (FUNCTION/EXIT/CH) and try again.

Previously programmed ³If a power failure occurs, programmed

information is erased. information may be erased. Reprogram if necessary.

You cannot store a name and phone number in the directory.

³You cannot store an item in the directory while the unit is in the talk mode.

³Do not pause for over 60 seconds while storing.

While programming or searching, the unit starts to ring and stops the program/ search.

³To answer the call, press (TALK). Start again from the beginning after hanging up.

The unit does not display the caller’s phone number.

³You do not subscribe to a Caller ID service.

³Other telephone equipment may be interfering with your phone. Disconnect it and try again.

³Other electrical appliances connected to the same outlet may be interfering with the Caller ID information.

³Telephone line noise may be affecting the Caller ID information.

³Some PABX units do not support Caller Display.

52

Image 52

Panasonic KX-TC1851ALB, KX-TC1851NZB operating instructions Before Requesting Help

Contents

Charge the battery for about 6 hours before initial use KX-TC1851NZB Before Initial Use Accessories includedFor your future reference For Best Performance Battery ChargeBase Unit Location/Noise Contents Useful Information Location of Controls Handset USE/CHARGE Indicator p Caller ID Indicator p , 20Base unit Antenna p Charge Contacts p Directory key DisplayTalk 01-06-35 0266667777 Waiting Settings Connections Installing the Battery in the Handset Battery strengthDisplay prompt Battery strength Fully charged Medium Low ﬂashing Needs to be recharged Battery information After your Panasonic battery is fully charged pOperation Approx. battery life Recharge Selecting the Line Mode Make sure the handset is in the standby mode Program Programmable FunctionsDuring programming Points to Talk switching Setting the Auto Talk FeaturePress Ý or Ü to select On or Off Selecting the Ringer Volume Ringer volumeSave directory 1Ringer volume 43 1=Yes Ringer Making Calls If noise interferes with the conversationTo redial the last number dialled Talk To select the receiver volume To dial after conﬁrming the entered numberTo redial after conﬁrming the last number dialled Loud Answering Calls Auto TalkBacklit LCD display Backlit handset keypad Caller ID Service How caller information is displayed when a call is receivedPrivate name display Display shows the caller’s phone number after the ﬁrst ring To check the number of new calls While the handset is on the base unitWhile the handset is off the base unit New calls 43 1=Directory Viewing the Caller List Using the Caller ListTo check who has called, follow the steps below Ex. When you search from the most recent call To return to the previous callerTo exit the Caller List, press Display meaning Calling Back from the Caller List Or Ü to enter the Caller ListPress Ý or Ü repeatedly to ﬁnd Desired caller For New Zealand Users Editing the Caller’s Phone Number 76543210 =Next 1=Edit0276543210 =Next 1=Edit 00276543210 =Next 1=Edit Advanced Operation Storing Caller List Information in the Directory Edit 1Save directory 43 1=Yes Enter name 21 4=Next To erase a speciﬁc caller from the Caller List Erasing Caller List InformationNew calls 43 1=Directory 0246813579 1220A JAN.12 √ Clear To erase all entries in the Caller List New call 43 1=Directory Exit 1All clear 43 1=Yes One-Touch Dialler Storing a Phone Number in the Direct ButtonPress Ý Next key 1234567890123456 =Edit 1=Save Save DIRECT# Dialling the Stored Number in the Direct Button Talk 1234567890123456 00-00-00 Using the Directory Storing Names and Numbers in the Directory Press Ý Next key Enter a phone number, up to 22 digits 1Save directory Ringer volume 43 1=Yes Directory= 20 itemsPress Ý Next key Press FWD/EDIT ß Save key For New Zealand Users If you make a mistake while entering a name Steps for Entering Names and SymbolsNumber of times key is pressed Keys For example, to enter Tom Jones Directory list =Caller’s list Finding Items in the Directory0312345678 Dialling from the Directory Index TableKeys Index Frank Talk Editing an Item in the Directory Erasing an Item from the Directory Directory item you want to erase pHelen Press Clear Press FWD/EDIT ß Yes key or Clear Special Features Automatic Security Code SettingHandset Locator To stop paging, press HANDSET\LOCATOR again or press Talk How to Use the Pause Button For Analog PBX Line/Long Distance Service UsersFor Call Waiting Service Users in New Zealand Call Waiting and Caller ID Compatible Selecting the recall time Recall Button1Program 43 1=Yes Points to Set recall time Press Ý or Ü repeatedly untilDesired time is displayed Save DIRECT# 1Set recall time 43 1=Yes Wall Mounting Wall TemplateTuck the telephone line cord inside Wall mounting adaptor, then To charge the battery To remove the handset holderPlace the handset on Handset holder as shown Using the Belt Clip Using the Optional HeadsetConnecting the optional headset to the handset To attach the belt clip To remove the belt clip Battery Replacement Adding Another Phone Before Requesting Help Problem Cause and RemedyClearer channel Before Requesting Help Recharge battery is For New Zealand Customers Safety Instructions SafetyInstallations Environment Placement Safety Instructions Medical For New Zealand Users Only Important Information For Australia only InstallationInstructions to customer Service difficulties 62, 4-chome, Minoshima, Hakata-ku, Fukuoka 812-8531, Japan PQQX12869YA-BM FM0800HK1090 D