ENGLISH-43

Adjustments and settings
42-ENGLISH
Use the Fand Gbuttons on the
projector or remote control unit to
select an item, then press the Ior
Hbuttons to change the setting.

OSD

ON
The current input name is displayed
in the top-right corner of the screen
when the input signal is changed.
OFF
Use this setting when you do not
want the current input name to be
displayed.

AUTO SIGNAL

This should normally be set to ON.
ON
AUTO SETUP will be carried out
automatically when the input signal
is changed.
OFF
AUTO SETUP will not function
when the input signal is changed.

AUTO KEYSTN

This should normally be set to ON.
ON
During automatic setup, the angle of
tilt of the projector is detected and
keystone distortion is corrected
automatically.
OFF
Use this setting when you do not
want automatic keystone correction
to be carried out during automatic
setup, such as when the screen
itself is at an angle.

AUTO RGB IN

This should normally be set to ON.
ON
During automatic setup, the
projector selects whichever one of
the RGB1 IN or RGB2 IN
connectors has a signal being input,
and uses that signal for projection.
(If a picture is being projected, the
signal source is not automatically
changed.)
OFF
Use this setting when you do not
want the signal source to be
changed automatically during
automatic setup.

RGB2 SELECT

This setting is used to select the
function of the RGB2 IN/RGB1 OUT
connector.
RGB2 SELECT INPUT
[
OUTPUT

RGB/YPBPR

This should normally be set to
AUTO. RGB or YPBPRis selected
automatically depending on the
synchronising signal status.
When HDTV, 525p (480p), 525i
(480i), 625i, 750p, and some
VGA480 signals are being
input, select “RGB” or “YPBPR” in
accordance with the input signal.

VGA60/525P

When a VGA60 or 525p RGB signal
is being input, select the signal in
accordance with the input signal.

SXGA MODE

This setting is only for an SXGA
signal.
SXGA
Select this item normally.
SXGA+
When the projected image is
contracted vertically, select this
item.
BLACKBOARD (PT-LC80E only)
Set to “ON” when PICTURE MODE
is set to BLACK-BD. (Refer to page
35.)

BACK COLOR

This sets the colour which is
projected onto the screen when no
signal is being input to the projector.

FRONT/REAR

This setting should be changed in
accordance with the projector
setting-up method.
Set to “FRONT” when using a
normal reflective screen with the
projector positioned in front of the
screen, and set to “REAR” when
using a translucent screen with the
projector positioned behind the
screen.

DESK/CEILING

This setting should be changed in
accordance with the projector
setting-up method.
Set to “DESK” when setting up the
projector on a desk or similar, and
set to “CEILING” when suspending
the projector from the ceiling using
the ceiling bracket which is sold
separately.

FAN CONTROL

Set FAN CONTROL to “HIGH”,
when using this projector at high
elevations (above 1400 m) only.

LAMP POWER

This setting changes the lamp
brightness. When set to “LOW”, the
RGB/YP
B
P
R
AUTO
[
RGB
[
YP
B
P
R
VGA60/525P 525P
[
VGA60
BACK COLOR BLUE
[
BLACK
FRONT/REAR FRONT
[
REAR
DESK/CEILING DESK
[
CEILING
LAMP POWER HIGH
[
LOW
SXGA MODE SXGA
[
SXGA+
FAN CONTROL STANDARD
[
HIGH
Option settings
OPTION1
OSD ON
AUTO SIGNAL ON
AUTO KEYSTN ON
AUTO RGB IN ON
RGB2 SELECT INPUT
RGB/YP
B
P
R
AUTO
VGA60/525P 525P
SXGA MODE SXGA
BLACKBOARD OFF
SELECT ADJ RETRN
OPTION2
BACK COLOR BLUE
FRONT/REAR FRONT
DESK/CEILING DESK
FAN CONTROL STANDARD
LAMP POWER HIGH
LAMP RUNTIME 100H
FUNC 1 INDEX
CONTROL KEY ON
AUTO POW.OFF DISABLE
SELECT ADJ RETRN