Control guide
Main unit
Standby indicator [^]
When the unit is connected to the AC mains supply, this indicator lights up in standby mode and goes out when the unit is turned on.
Standby/on switch [8]
Press to switch the unit from on to standby mode or vice versa.
In standby mode, the unit is still consuming a small amount of power.
[SPEAKERS, A, B]
For selecting speakers A or B.
Turning the speakers off automatically engages the STEREO/2CH MIX mode (when listening through headphones, for example).
[% DIGITAL EX, % DIGITAL, % PL Ⅱ, DTS 96/24,
Lights to indicate the source’s input signal and decoding format used.
%DIGITAL EX: Dolby Digital Surround EX sources
%DIGITAL: Dolby Digital sources
%PL Ⅱ : Dolby Pro Logic Ⅱ decoder is being used DTS 96/24: DTS 96/24 sources
DTS: DTS sources
DTS NEO:6: DTS NEO:6 matrix decoder is being used
[MULTI CONTROL]
Press to enter Multi control mode, and use [INPUT SELECTOR] to select/enter.
[INPUT SELECTOR]
For selecting input. Selects/Enters each setting in Multi control mode.
[VOLUME]
Volume control.
Remote control signal sensor
|
|
|
| MULTI CONTROL | INPUT SELECTOR | VOLUME |
|
SPEAKERS |
|
|
|
|
|
| |
A | B |
|
|
|
|
|
|
|
|
|
| PUSH ENTER |
|
|
|
6.1CH DECODING |
|
|
|
|
|
|
|
|
|
|
|
|
| DOWN | UP |
VCR 2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
| PHONES |
| VIDEO IN | L | AUDIO IN | R |
|
|
|
[VCR 2]
For a video camera, etc.
[6.1CH DECODING]
For turning on the 6.1 channel decoding mode. When using this mode the indicator lights.
[BASS SYNTHESIZER]
For turning on the bass synthesizer mode. When using this mode the indicator lights.
[MULTI-SOURCE RE-MASTER]
For selecting a
[TUNE 2, 1]
For tuning the radio and selecting preset stations.
Press and hold until the frequency starts scrolling to start automatic tuning. Tuning stops when a station is found.
[PHONES]
Headphone jack
Plug type: 6.3 mm stereo
• Avoid listening for prolonged periods of time to prevent hearing damage.
•Turn the speakers off
when using the headphones.
Display
• When you turn the dimmer to “ON”, the following indicators change to dim.
Operations
[– SPEAKERS– , ]
Speaker indicators
:Sound is output from speakers connected to the front A, surround, and center terminals.
: Sound is output only from speakers connected to the front B terminals.
:Sound is output from speakers connected to the front A and B terminals.
[TUNED, ST, , MONO]
Radio indicators
TUNED: A station is tuned.
ST: A stereo FM broadcast is tuned.
: Flashes during automatic presetting.
MONO: Lights when using the monaural mode.
[SLEEP]
Sleep timer indicator.
[ RDS , PS, PTY]
(For continental Europe and the United Kingdom)
RDS : Lights while RDS signals are being received.
PS, PTY: Indicates the current RDS display mode.
[SFC, CENTER FOCUS, 2CH MIX,
MULTI REAR]
SFC: Lights when using an SFC mode.
CENTER FOCUS: Lights when using the center focus mode.
2CH MIX: Lights when playing a multi- channel source in 2CH MIX mode.
MULTI REAR: Lights when using the multi rear surround mode.
[<<<MULTI CONTROL>>>]
When you press the [MULTI CONTROL] button and enter the settings the indicator lights.
[–DIGITAL INPUT–, L, C, R, S,
LS, SB, RS, LFE]
Program format indicators
Show the channels contained in the digital input signal. They do not light when input is analogue.
L:Front left channel
C:Center channel
R:Front right channel
S:If the surround channel is monaural.
LS: Surround left channel
SB: Surround back channel
RS: Surround right channel
LFE (Low Frequency Effects):
RQT7492
14 |
[TAPE MONITOR]
Lights when the tape monitor is on.
General display
Shows the input mode, radio frequency, and other general information.
SPEAKERS
A B
TAPE MONITOR
TUNED ST M | SFC CENTER FOCUS | DIGITAL INPUT | ||
MONO SLEEP | 2CH MIX MULTI REAR | L | C | R S |
RDS PS PTY | MULTI CONTROL | LS | SB | RS LFE |
DIGITAL | fs |
PROCESSING |
kHz
MHzkHz
[DIGITAL PROCESSING fs]
Displays the frequency the unit is processing.
[kHz, MHz]
Frequency unit indicators
kHz: AM, or PCM sampling frequency
MHz: FM
