Panasonic SC-BTT190 manual Picture, The unit switches to standby mode, The unit does not turn off

The unit switches to standby mode.

¾This unit will automatically turn to standby mode after 30 minutes if it is inactive. (> 18)

¾When the time set for the sleep timer has passed, the main unit will be turned off. (> 8)

¾One of the unit’s safety devices is activated. Press [Í/I] on the main unit to turn the unit on.

The unit does not turn off.

1Press and hold [Í/I] on the main unit for 5 seconds. (If still unable to turn the unit off, disconnect the AC mains lead, wait 1 minute,

then reconnect the AC mains lead.)

2Reset the unit as follows:

While the unit is off, press and hold [+ VOLUME], [< OPEN/CLOSE] and [Í/I] on the main unit at the same time for more than 5 seconds.

Picture

The images from this unit do not appear on the TV.

Picture is distorted. Jittering occurs.

¾An incorrect resolution is selected in “HDMI Video Format”. Reset the setting as follows:

1While the unit is on, press and hold [OK], the yellow button and the blue button on the remote control at the same time for more than 5 seconds.

j“00 RET” is displayed on the unit’s display.

2Repeatedly press [1] (right) on the remote control or [Í/I] on the unit until “04 PRG” is

displayed on the unit’s display.

3Press and hold [OK] on the remote control or [< OPEN/CLOSE] on the unit for at least

3 seconds.

Set the item again. (> 32)

jWhen Dolby Digital Plus, Dolby TrueHD, and DTS-HD audio are not output in bitstream, select “Yes” in “Default Settings” and make proper settings. (> 36)

¾The unit and television are using different

video systems.

1While the unit is on, press and hold [OK], the yellow button and the blue button on the remote control at the same time for more than 5 seconds.

–“00 RET” is displayed on the unit’s display.

2Repeatedly press [1] (right) on the remote control or [Í/I] on the unit until “05 P/N” is

displayed on the unit’s display.

3Press and hold [OK] on the remote control or [< OPEN/CLOSE] on the unit for at least

3 seconds.

The system switches from PAL to NTSC or vice versa.

¾The system used on the disc doesn’t match your television.

jPAL discs cannot be correctly viewed on an NTSC television.

¾When “3D BD-Video Playback” in the Setup menu is set to “Automatic”, images may not be output depending on the connection method. After removing the disc from this unit, select “Set before play” in the Setup menu, and select “2D Playback” in the setup screen displayed when playing 3D discs. (> 33)

¾If irregular colouring occurs on your TV, turn the TV off for about 30 minutes.

If it persists, move the speakers further away from the TV.

Video is not output in high-definition.

¾Confirm that “HDMI Video Format” in the Setup menu is set properly. (> 32)

3D video is not output.

¾Change the settings as required by the connected TV format. (> 33, “3D Type”)

¾Are the settings on this unit and the TV correct? (> 21)

¾Depending on the connected TV, the video being played back might switch to 2D video due to changes in resolution etc. Check the 3D setting on the TV.

¾Check that proper HDMI video input is selected on the TV.

3D video is not output correctly as 2D.

¾Select “Set before play” in the Setup menu, and select “2D Playback” in the setup screen displayed when playing 3D discs. (> 33, “3D BD-Video Playback”)

¾Discs that have recorded titles with Side by side (2 screen structure) and that can be enjoyed in 3D are played back in accordance with the settings of the TV.

A black band is displayed around the edge of the screen.

The aspect ratio of the screen is abnormal.

¾Confirm the “TV Aspect” is set properly. (> 35)

¾Adjust the aspect setting on the television.

Reference

VQT4D57 41