Press [FM/AM] to select “FM” or “AM”.

The radio

Press [TUNER] to put the remote control in TUNER mode.

 

 

TV

INPUT SELECTOR

 

 

 

 

DVD/VHS FM/AM

FM/AM

 

 

 

 

 

 

DVD

VHS

TV

TUNER

TUNER

 

 

 

 

 

Numbered

1

2

3

 

CH

buttons

 

 

 

CH

4

5

6

 

CH

 

 

 

PICTURE MODE

 

VOLUME

 

 

7

8

9

 

 

 

 

 

SETUP

ENTER

 

 

 

DISC

0

S10

 

 

 

SKIP

SLOW/SEARCH

 

 

OPEN/CLOSE/EJECT

JET REW

 

 

 

TOP MENU

 

 

MENU

 

ENTER

NAVI

 

 

 

 

NAVIGATOR

 

 

LIST

 

 

DIRECT

 

 

PLAY

 

 

 

ENTER

 

 

 

STATUS/

 

 

RETURN

 

 

FUNCTIONS

 

 

 

 

TV VOL

 

 

TV VOL

 

 

MULTI RE-MASTERMIX 2CH PROGRESSIVE REPEAT

 

 

QUICK OSD

ZOOM

CD MODE

PLAY MODE

PLAY MODE

 

 

 

 

 

 

H.BASS

C.FOCUS

TEST

CH SELECT

 

H.BASS

SUBWOOFER LEVEL SFC

SUPER SRND

MUTING

CH SELECT

 

 

 

 

 

C. FOCUS

 

ADVANCE

QUICK

REC

TEST

CM SKIP

DISC REVIEW

REPLAY

SFC

PROG

SPEED

 

 

SUPER SRND

SHIFT

SLEEP

AUDIO

RESET

SHIFT

PL

TV/VIDEO

 

 

 

CANCEL

 

 

PL

INPUT SELECTOR

OPEN/CLOSE

 

 

 

 

EJECT

DISC CHECK

 

 

 

 

 

H.BASS

 

/REW

FF/

REC

VOLUME

 

 

 

 

 

STOP

PLAY

STOP

PLAY

 

 

 

 

 

 

CH

 

-DEMO

 

PHONES

DOWN

UP

1 Tune to the station (l above).2 Press [ENTER].

3 While “PGM” is blinking on the display

Press the numbered buttons to select a channel.

Alternatively, press [W CH] or [X CH] then press [ENTER].

The station occupying a channel is erased if another station is preset to that channel.

1 Press [FM/AM] to select “FM” or “AM”.2 Press the numbered buttons to select the channel.

Alternatively, press [W CH] or [X CH].

To select a 2-digit number

e.g. 12: [S10] l [1] l [2].

When a stereo FM broadcast is being received.

Automatic presetting

Up to 15 stations can each be set in the FM and AM bands.

1 Press [FM/AM] to select “FM”.

2 Press [6] or [5] to tune to the lowest frequency (“FM 87.9” MHz or “FM 87.5” MHz).

3 Press and hold [ENTER].

Release the button when “AUTO” is displayed.

The tuner presets all the stations it can receive into the channels in ascending order.

≥“SET OK” is displayed when the stations are set. The last station to be set is then played.

≥“ERROR” is displayed when automatic presetting is unsuccessful. Preset the channels manually (l right).

4 Repeat steps 1 to 3 to set the AM bands (the lowest frequency is “AM 520” kHz).

Manual tuning

1

2 Press [6] or [5] to select the frequency.

Press and hold [6] or [5] until the frequency starts scrolling to start automatic tuning. Tuning stops when a station is found.

RQT7921

∫If noise is excessive in FM

Press [PLAY MODE] to display “MONO”.

Press [PLAY MODE] again to cancel the mode.

The mode is also canceled when you change the frequency.

∫FM frequency step

Main unit only

The step is factory-set to 0.2 MHz, but you can change it to receive broadcasts allocated in 0.1 MHz steps.

1Press [INPUT SELECTOR] on the main unit to select “FM”.

2Press and hold [INPUT SELECTOR].

After a few seconds the display changes to show the current minimum frequency. Continue to hold the button down. The

minimum frequency changes and the step is changed. To return to the original step, repeat the above steps.

[Note]

Any FM/AM frequencies preset in channels will be changed by this procedure. Preset them again.

40