Simple Setup
Speaker installation options |
|
| |
∫ Attaching to a wall |
| Front and surround speaker [HT995W] | Center speaker [HT995W] |
You can attach all of the speakers (except subwoofer) to a wall. |
|
| |
≥The wall or pillar on which the speakers are to be attached |
|
| |
should be capable of supporting over 15 kg ([HT995W] 10 kg) per | 106 mm |
| |
screw. Consult a qualified building contractor when attaching the |
| ||
|
| ||
speakers to a wall. Improper attachment may result in damage to |
|
| |
the wall and speakers. |
|
| 200 mm |
≥When mounting the front speakers or surround speakers to a |
|
| |
wall, we recommend using a string (not included) to prevent it | 340 mm |
| |
from falling. |
|
| |
[HT995W] 4 Screws | [HT995W] 4 Cover plates |
|
|
Assembling the front and surround speakers
RQT8766
8
Preparation for front and surround speakers [HT995]
1 Pull down the longer
part of the cable to release the cable from the groove inside the
stand, and then pull the speaker cable out from the stand.
2 Feed the cable into the bottom of the speaker and through the slot at the rear.
3 Connect the cable (➜ page 6).
[HT995W]
1 Remove the speaker cable from the stand.
Release the cable from the groove.
2Connect the cable (➜ page 7).
1 [HT995W] Attach the cover plate to the front speaker or surround speaker.
Cover plate | Screw |
Tighten securely.
2Drive a screw (not included) into the wall.
‰4.0 mm ‰7.5 to 9.5 mm
Wall or pillar | 5.0 to 7.0 mm |
3Fit the speaker securely onto the screw(s) with the hole(s).
Front and surround speaker [HT995] | Center speaker [HT995] | |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
255 mm
190 mm
320 mm
e.g. | In this position, the | Move the speaker |
| ||
| speaker will likely | so that the screw is |
| fall if moved to the | in this position. |
| left or right. |
|
Reattaching the speaker cable to the stand
[HT995]
1 Remove the two screws from the stand, and remove the metal cover.
Screw | Screw |
Metal cover
Plastic cover
2Pull the cable out about 40 cm from the hole in the metal cover, and insert the plastic cover.
| Approx. 40 cm |
|
3 | Insert the metal cover |
|
| so it does not disturb |
|
| the cable and close |
|
| tightly with the two screws. |
|
[HT995W] |
| |
1 | Remove the eight screws | Screw |
| from the stand, and remove |
|
| the speaker net. |
|
2 | Position the cable. |
|
Press the cable into the groove.
Approx. Cable 15 cm
3 Attach the speaker net with the screws.
∫Fitting speaker stands (not included)
(For center speaker)
Ensure the stands meet these conditions before purchasing them. Note the diameter and length of the screws and the distance between screws as shown in the diagram.
≥The stands must be able to support over 10 kg.
≥The stands must be stable even if the speakers are in a high position. e.g. Center speaker [HT995]
Metal screw holes
For attaching to speaker stands
5 mm, pitch 0.8 mm
Plate thickness plus |
|
7 mm to 10 mm | 60 mm |
Speaker stand
(not included)