Specifications
g AMPLIFIER SECTION RMS Power output
10% Total harmonic distortion
1 kHz, both channels driven
(Low channel) | 35 W per channel (6 Ω) |
8 kHz, both channels driven | |
(High channel) | 35 W per channel (6 Ω) |
Total | 70 W per channel |
Input sensitivity |
|
AUX | 250 mV |
Input Impedance |
|
AUX | 11.8 kΩ |
g FM TUNER SECTION
Frequency range | 87.9 - 107.9 MHz |
Sensitivity | 1.8 µV (IHF) |
S/N 26 dB | 1.5 µV |
Antenna terminal(s) | 75 Ω (unbalanced) |
g AM TUNER SECTION
Frequency range | 530 - 1710 kHz |
Sensitivity |
|
S/N 26 dB (at 999 Hz) | 560 µV\m |
g CASSETTE DECK SECTION
Track system |
| 4 track, 2 channel |
Heads |
|
|
Record/playback |
| Solid permalloy head |
Erasure | Double gap ferrite head | |
Motor |
| DC servo motor |
Recording system |
| AC bias 100 kHz |
Erasing system |
| AC erase 100 kHz |
Tape speed |
| 4.8 cm/s |
Overall frequency response | ||
(+3 dB, | ||
NORMAL (TYPE I) |
| 35 Hz - 14 kHz |
S/N |
| 50 dB (A weighted) |
Wow and flutter |
| 0.18% (WRMS) |
Fast forward and rewind time | ||
Approx. 120 seconds with | ||
g CD SECTION |
| |
|
| |
Disc played |
|
|
CD/MP3/WMA |
| 8cm/12cm, |
Sampling frequency | 44.1 kHz | |
Decoding |
| 16 bit linear |
Pickup |
|
|
Beam source/wavelength
Semiconductor laser/780 nm
Number of channels | Stereo | |
Frequency response |
| |
| 20 Hz - 20 kHz (+1, | |
Wow and flutter | Below measurable limit | |
Digital filter |
| 8 fs |
D/A converter |
| MASH (1 bit DAC) |
MP3 |
|
|
Bit rate |
| 32 kbps - 320 kbps |
Sampling frequency |
| |
| 32 kHz, 44.1 kHz, 48 kHz | |
WMA |
|
|
Sampling frequency |
| |
| 32kHz, 44.1kHz, 48kHz |
g SPEAKER SECTION
Type | 2 way 2 speaker system | |
Speaker(s) |
|
|
Woofer |
| 10 cm cone type |
Tweeter |
| 6 cm cone type |
Impedance |
|
|
HIGH |
| 6 Ω |
LOW |
| 6 Ω |
Input power |
|
|
HIGH |
| 70 W (Music) |
LOW |
| 70 W (Music) |
Output sound pressure level | ||
|
| 80 dB/W (1.0 m) |
Cross over frequency | 3.5 kHz | |
Frequency range |
|
|
| 55 Hz - 31 kHz | |
| 75 Hz - 26 kHz | |
Dimensions (W x H x D) | ||
|
| 155 x 250 x 258 mm |
Mass |
| 2.3 kg |
g GENERAL
Power supply | AC 120 V, 60 Hz) |
Power consumption | 130 W |
Dimensions (W x H x D) | |
| 179 x 247 x 378 mm |
Mass | 5.4 kg |
| |
Power consumption in standby | |
mode: Approx. 0.6 W |
|
Note
1.Specifications are subject to change without notice.
Mass and dimensions are approximate.
2.Total harmonic distortion is measured by the digital spectrum analyzer.
3.The labels “HIGH (HF)” and “LOW (LF)” on the rear of the speakers refer to High frequency and Low frequency.
When moving the unit
1.Remove all discs.
2.Press [8] to turn the unit off.
3.Disconnect the AC mains lead.
Maintenance
For a cleaner crisper sound
Clean the heads regularly to assure good quality playback
and recording.
Use a cleaning tape (not included). If the surfaces are dirty
To clean this unit, wipe with a soft, dry cloth.
• | Never use alcohol, paint thinner or |
| benzine to clean this unit. |
• | Before using chemically treated |
| cloth, read the instructions that |
| came with the cloth carefully. |
This product may receive radio interference caused by mobile telephones during use. If such interference is apparent, please increase separation between the product and the mobile telephone.
RQT7372
26
Product Service
1.Damage requiring service - The unit should be serviced by qualified service personnel if:
(a)The AC power supply cord or the plug has been damaged; or
(b)Objects or liquids have gotten into the unit; or
(c)The unit has been exposed to rain; or
(d)The unit does not operate normally or exhibits a marked change in performance; or
(e)The unit has been dropped or the cabinet damaged.
2.Servicing - Do not attempt to service the unit beyond that described in these operating instructions. Refer all other servicing to authorized servicing personnel.
3.Replacement parts - When parts need replacing ensure the servicer uses parts specified by the manufacturer or parts that have the same characteristics as the original parts. Unauthorized substitutes may result in fire, electric shock, or other hazards.
4.Safety check - After repairs or service, ask the servicer to perform safety checks to confirm that the unit is in proper working condition.
The servicer will require all components to service your system. Therefore, should service ever be necessary, be sure to bring the entire system.
Product information
For product information or assistance with product operation:
In the U.S.A., refer to “Customer Services Directory” on page 27. For assistance in the continental U.S.A in obtaining repairs please ship the product to:
Panasonic Services Company - Customer Servicenter Suite B 4900 George McVay Drive, MacAllen, TX 78503
In Puerto Rico contact the Panasonic Sales Company. Tel. (787)
When shipping the unit carefully pack and send it prepaid, adequately insured and preferably in the original carton. Include a letter detailing the complaint and provide a day time phone number where you can be reached.
IF REPAIR IS NEEDED DURING THE WARRANTY PERIOD THE PURCHASER WILL BE REQUIRED TO FURNISH A SALES RECEIPT/ PROOF OF PURCHASE INDICATING DATE OF PURCHASE, AMOUNT PAID AND PLACE OF PURCHASE. CUSTOMER WILL BE CHARGED FOR THE REPAIR OF ANY UNIT RECEIVED WITHOUT SUCH PROOF OF PURCHASE.
Also, the purchaser will be responsible for shipping the unit to the above address. In Canada, contact Panasonic Canada Inc. Customer Care Centre at