![](/images/new-backgrounds/1305635/305635101x1.webp)
Check that the network settings are as shown below, and then start “Connection test”.
Select “Connection test” and press OK.
*Press OK again to cancel the test. (It takes a while to cancel the test.)
Network setting | 1/2 | select | |
Connection test | Succeeded |
| |
IP setting mode | Manual | ok | |
IP address | 192.168.0.5 | ||
| |||
Subnet mask | 255.255.255.0 |
| |
Default gateway | 192.168.0.254 |
|
Succeeded: “Connection test” succeeded Only home network:
Home network is available.
Failed: Check the broadband environment connection and settings and the network settings, and then perform the test again.
Test in progress
Select “IP setting mode” and set to “Automatic”.
(When IP automatic acquisition in DHCP can be used)
| Network setting |
|
| 1/2 | select | |
| Connection test |
| Succeeded |
|
| |
| IP setting mode |
| Automatic |
|
|
|
| IP address |
|
|
| ok | |
| Subnet mask |
|
|
| ||
| Default gateway |
|
|
|
| |
|
|
|
|
|
|
|
■Manual setting
Select “IP setting mode” and set to “Manual”
Select the item and press OK
Check the specifications of the broadband router and enter each IP address.
| Subnet mask |
| 0 | . | 0 . | 0 . | 0 |
|
|
|
|
|
|
|
|
|
|
The acquired address is displayed.
Each IP address is acquired automatically. | or | change |
| channel | |
|
| ok |
Network
Select “DNS setting mode” and set to “Automatic”.
(When DNS automatic acquisition in DHCP can be used)
|
|
|
|
| select |
| Network setting | 1/2 |
| ||
| Connection test |
| Succeeded |
| |
| Default gateway | 192.168.0.254 |
|
| |
|
|
| Automatic |
|
|
|
|
|
|
|
|
| DNS setting mode |
| Automatic |
| ok |
| Primary DNS |
|
| ||
|
|
|
|
| |
| Secondary DNS |
|
|
| |
|
|
|
|
|
|
The acquired address is displayed.
■Manual setting
Select “DNS setting mode” and set to “Manual”
Select the item and press OK
Enter each IP address as was specified by the provider.
| Primary DNS | 0 | . 0 . 0 . | 0 |
Setting
Each IP address is acquired automatically. | or | select |
If you are using a broadband router, IP automatic |
| ok |
acquisition in DHCP can be used under normal |
| |
|
| |
circumstances. If you are not sure, check with the |
|
|
person who installed the equipment, or check the |
|
|
instructions for each device. |
|
|
Advanced
Select “LAN speed setting” (Default is “Automatic”)
|
|
| select |
Network setting | 2/2 | ||
LAN speed setting | Automatic |
|
|
|
|
|
|
LAN speed |
|
| |
Software update |
|
| adjust |
MAC address |
| ||
|
|
|
|
Normally, select “Automatic”.
If “Connection test” failed, set the “LAN speed setting” to “manual” and then select “10BASE half duplex”, “10BASE duplex”, “100BASE half duplex” or “100 BASE duplex”.
Cannot be selected when the “LAN speed setting” is “Automatic”.
Changing the settings may make it impossible to connect some types of equipment.
Select “Software update” |
| Press OK to start the software update screen. | |||
|
|
|
| select | Follow directions of the screen. |
Network setting | 2/2 |
| |||
LAN speed setting | Automatic |
|
|
| * Set “Clock” first. (p. 24) |
LAN speed |
|
|
| ||
|
|
|
| ||
Software update |
|
|
| ok |
|
|
|
|
|
| |
MAC address |
|
|
| ||
|
|
|
|
|
|
The network settings become effective when you close the menu and run “Connection test”.
51