Connections, Audio OUT Terminals connection | Panasonic TH-103PF9UK

Connections

AUDIO OUT Terminals connection

Speakers (Optional accessories)

AC cord connection (see page 13)

RL

AUDIO OUT

Stereophonic sound code

audio equipment

line-in

– AC cord ﬁxing

			Close	Close
				Push until
				the hook clicks.
	1 Plug the AC cord into		Open	Open
		the display unit.	Open	Open
Note:		Plug the AC cord until		2. Pull off.
Note:		it clicks.		1. Keep the
Make sure that the AC	2	Fix the AC cord with		1. Keep the
cord is locked.	2	Fix the AC cord with		knob pressed.
cord is locked.		the clamper.		knob pressed.

– Cable ﬁxing bands

Unplug the AC cord

Unplug theAC cord pressing the two knobs.

Secure any excess cables with bands as required.

Pass the attached cable ﬁxing band through the clip as shown in the ﬁgure.

1

To secure cables connected to Terminals, wrap the cable ﬁxing band around them then pass the pointed end through the locking block, as shown in the ﬁgure.

While ensuring there is sufﬁcient slack in cables to minimize stress (especially in the power cord), ﬁrmly bind all cables with the supplied ﬁxing band.

To tighten:	To loosen:
	Push the catch
Pull
2	Pull

	AUDIO	R AUDIO L	PR/CR/R PB/CB/B	Y/G	AUDIO		R	L
					AUDIO		R	L
	DVI-D IN	COMPONENT/RGB IN
SLOT1	SLOT2		SLOT3	PC	IN	SERIAL	AUDIO OUT

Optional TerminalDVI-D

INDVI-D INCOMPONENT/RGBCOMPONENT/RGBIN OptionalIN

FromTerminalEXTERNALFrom

EXTERNALFrom SERIAL

From

SERIALFrominput on

Board InsertTerminalsSlot Terminalsand AudioandINAudioTerminalsIN TerminalsBoard

monitorInsert Slotterminalmonitor

terminalTerminalon on ComputerTerminalaudioon Coampliuterﬁ

(covered) (see page(see12)page(see12)page(see12)page 12)

(covered)

Computer (see pageComputer10)

(seepage10)11)

(see page(see11)page 9)

Note:

At factory shipment, Terminal boards are installed in SLOT 2 and SLOT 3

9

Image 9

Panasonic TH-103PF9UK manual Connections, Audio OUT Terminals connection, Close, Open

Contents

Operating Instructions High Deﬁnition Plasma DisplayModel No. TH-103PF9UK English Risk of Electric Shock Do not Open Important Safety Instructions Table of Contents FCC Caution Canadian NoticeTrademark Credits Safety Precautions When using the Plasma DisplayTake steps to prevent toppling Safety Precautions / Maintenance MaintenanceSetup AC Power Supply Cord Accessories Accessories SuppliedRemote Control Batteries Audio OUT Terminals connection ConnectionsClose Open Signal Names for Mini D-sub 15P Connector PC Input Terminals connectionConnections Serial Terminals connection CommandCommunication parameters Basic format for control data DVI-D Input Connector Component / RGB connection & RGB signal R, G, BSignal Name DVI-D connection Connecting the AC cord plug to the Plasma Display Power on / OFFConnecting the plug to the Wall Outlet Right side surface On OFF Basic Controls Basic Controls On-Screen Menu Displays Advanced SettingsRight side Sound POS. /SIZE On-Screen Menu Displays Power on Time Power OFF Time Initial selections Selecting the input signalSelecting the On-Screen Menu Language INPUT1 INPUT2 INPUT3 PC Aspect Controls Mode Picture ExplanationNormal Zoom Full Normal Full Size / DOT Clock / Clock Phase / 11 Pixel Mode Adjusting POS. /SIZEPress to adjust POS. /SIZE During COMPONENT, RGB and PC input signal Clock Phase Adjusting POS. /SIZEPOS Size Picture which you would like to change input modes Under main Picture and sub picture display, select Sub screen Main screen Advanced PIP Standard Picture AdjustmentsDynamic Cinema Picture Adjustments Advanced Settings Mute Sound Adjustment Display the Operation Guide Digital ZoomSelect the magniﬁcation required for the enlarged display Return to normal display quit Digital Zoom Present Time Setup Press to set up Present Time of DAYPress to select Set Display the SET UP Timer Screen Press to select SET UP TimerPower on Time / Power OFF Time Press to select Power on Function Start setting Mode selectionScreensaver For preventing after-images Negative / Scroll selection Press to display the SET UP menu Setup of Screensaver TimeReduces screen after-image Screensaver For preventing after-images Side BAR Adjust OFF Dark MID BrightPress to exit from Screensaver Reduces power consumption Customizing the Input labelsAddition sign Selected Input How to setup Multi Display SET UP for Multi DisplayGroup of 4 2 × Group of 9 3 × Group of 16 4 × Press to select on or OFF Press to select Seam Hides Video SET UP for Multi DisplayPress to select OFF, on Display Number locations for each arrangement Examples ID Remote Control Function Seam Hides Video SettingID remote control button operation ID Cancellation Component / RGB in Select SET UP for Input Signals3D Y/C Filter For Ntsc AV images Component RGB Color System / Panasonic Auto SET UP for Input SignalsPulldown / Video NR Color System Sync Setting RGB sync signalFREQ. kHz / V-FREQ. Hz Displays the H Horizontal / V Vertical frequencies Options Adjustments Options Adjustments Locks Buttons on bottom face of main unit NormalizationOff User1 User2 User3 Remocon User1You can only use Shipping condition Symptoms Checks TroubleshootingSymptoms Check Plasma Display panel DVI-D∗3 DVI-D/COMPONENT/RGB/PC input signals Speciﬁcations Memo Panasonic Broadcast & Television Systems Company Customer’s RecordExecutive Ofﬁce Panasonic Canada Inc