Manuals / Sears / Power Tools / Saw

Sears 113.197511, 113.197611, 113.197411 owner manual Install Battery, To Replace Battery

Models: 113.197411 113.197511 113.197611

1 104

Download 104 pages 10.3 Kb

Page 49

Digital Display

Install Battery

1. Set out -battery

-battery. cover.

2.Position battery with angled corner on top right and slide battery all the way into opening behind digital display, pushing slightly downward until it snaps into place.

3.Look at display. It should look like this: If it shows nothing, push in and slightly

upwards on battery to remove it, then re- install.

If there still is no display, remove bat- tery, wipe off contacts, then re-install.

If there is still no display, try a new 6V alkaline battery or contact Sears.

4.When display shows correctly, snap bat- tery cover into place.

5.Follow steps to align encoders and set zero reference points.

To Replace Battery

I. lJse screwdriver to pry off battery cover.

2.Push in and slightly upwards on battery to remove it. Install new 6V alkaline bat- terv.

3.Follow steps to set zero reference

poi nts.

49

Image 49

Sears 113.197511, 113.197611, 113.197411 owner manual Install Battery, To Replace Battery

Contents

113.197611 113.197511Part No. SP5539 Contents Safety Symbol and Signal Words SafetyMajor Hazards Wrong Way Feed Hazard KWARNING Personal Safety Instructions Safety InstructionsWork Area Safety Instructions Workpiece Safety Instructions Saw Safety Instructions Blade Safety Instructions KWARNING On-Product Safety Labels Safety Identify Parts Assembly QJlIF*llfq!lt LHllLltlLllltllllltB Tools Needed For Assembly Build Cabinet Base Assembly Steps Build Foot Assemblies Shaped Slot Attach Foot Assemblies Short Assemble Side PanelsOnly Door Model without Casters Attach Door Hinges Assembly Attach Side Panels to Bottom Shelf Attach/Install Spacers Attach Skirts Center Support Upper Lower Attach Doors Complete Center Slide AssemblyOnly Drawer Model Center Support Attach Handwheel Assemble Drawers Shaft has left-hand threa&. Turn nut clock- wise to loosen Mount Motor Mount Basic Saw Assembly Assembly Attach Trim Caps Adjust Leveling Feet Attach Slide Arm Supports Install Front Table Clips. Note Table will extend about Beyond Trim caps Assemble Table Lock Mechanism Install Drawers Only Drawer Model Alignment and AdjustmentTo Remove Drawers Only Drawer Model 45, -45 , 90 Controls Rip l.ock Controls Alignment and Adjustment Steps Alignment and AdjustmentAdjust Column Support Level Front Table Square Crosscut Travel Square Blade to Table for Crosscut- ting Install Blade Alignment and Adjustment Square Blade to Fence Square Blade to Table for Ripping Adjust Carriage Bearings Make Blade Parallel to Table Align Spreader to Blade Install Guard Go to Digital Display Section and follow Complete Adjustments Digital Display Error MessagesButton Functions =73 To Replace Battery Install Battery Miter Encoder Align Encoders Bevel Encoder Set Zero Reference Points For Bevel, Miter, and Elevation Set Zero Reference Point For Out-Rip Set Zero Reference Point For Rip Conversion Table Power Supply Motor Specifications Electrical Connections Motor Protection & Reset Button To avoid electric shock, unplug saw To Change Motor Voltage to 240 A.CBefore changing Motor voltage Crosscutting Crosscutting SafetyDuring crosscutting, blade teeth can Having fingers, hand or arm cut off Crosscut Kerfs Crosscuttin Step Making Crosscuts Repetitive Crosscutting Ripping Defined RippingIn-Rip and Out-Rip Positions Infeed and Outfeed Directions Workpiece Positioning Ripping Safety Pinching or binding can happen when Kickback Wrong Way Feed Ripping Pawls and Spreader Function Guard Nose Function If workpiece is pushed along fence Ripping Set-up ProcedureWith kerfs, workpiece could get Inleed Making Rip Cuts Dado Blades, Molding Heads Ripping Hints Fences Cutting AidesPush Sticks Auxiliary Fence and Push Block for Ripping Cutting Aides Straight Edge for Irregular Workpiece Cutting Aides Information for Dado Accessories SafetyInformation for Edging Edging without an auxiliary fence Lower Blade Guard Lower blade guard can get caught or AccessoriesJam in fence or table kerfs Cleaning MaintenanceGeneral Information Lubrication Remove screw and nut from swivel lock knob Adjustments for Wear Arm and Column Carriage Bearings Replacing Pawls Blade Changing Possible Causes Motor ProblemWhat to Do Troubleshooting Cutting Problem TroubleshootingSaw Problem Possible Causes Electronics Problem Troubleshooting Blank Model NOS .197411 and 113.197511 Repair Parts Always order by Part Number Not by Key Number Repair Parts Model NOS .197411 and 113.197611 Base and Column Assembly Model NOS .197411 and 113.197511 Model NOS .197411 and 113.197611 Parts List for Craftsman 10 Electronic Radial SAW Model NOS .197411 and 113.197511 Part Model NOS .197411 and 113.197611 and 113,197511 Repair Parts ARM Assembly Table Assembly Foot Assembly Model 113.197511 Model NOS .197411, 113.197511 Model NOS .197411, 113.197511 Repairs Parts Repairs Parts Cabinet Assembly for Model 113.197411 Model For Motor Assembly Guard Assembly Index 113.197411 Sold by SEARS, Roebuck and CO., Chicago, IL 60684 U.S.APail No. SP5539