Manuals / Brands / Power Tools / Saw / Sears / Power Tools / Saw

Sears 113.197411, 113.197511, 113.197611 Troubleshooting

1 104

Download 104 pages, 4.64 Mb

Troubleshooting

Electronics Problem

No display when ON/OFF button

pushed

Possible Cause(s)

Battery incorrectly installed

Bdttery contacts dirty

Dead battery

Display failure

What to Do

Install battery correctly

Clean battery contacts

Replace with 6V, size Jbattery

Have electronics checked by Sears

Display shows: ele --.-- Normal at battery installation

Reference points not set

Poor battery contact

Display failure

No action

Set "0"reference points

Clean battery contacts

Have electronics checked by Sears

Display dim Low battery voltage

Saw very cold

Replace with 6V, size Jbattery

Allow saw to warm above 32°F

Display dark Saw very warm Allow saw to cool below 120°F

Display blanks after a few minutes Normal Push ON/OFF to see display

Display blanks when moving car-

riage, then re-appears when mo-

tion stops

Normal when position is changed

rapidly No action

Display shows: EEE.E or EE.EE Arm or carriage moved abruptly

or too rapidly when display is off Re-set "0" reference point(s)

Display resets but immediately

shows EEE.E or EE.EE when

carriage is moved

Defective encoder or display in-

dicator Have electronics checked by Sears

Display does not change when

arm or carriage ismoved Wrong function selected

Defective encoder or display in-

dicator

Select correct function

IIave electronics checked by Sears

Display does not read 0° or

45° at bevel or miter indexes "0"reference points not set at in-

dexed points Set "0"reference points

Miter anti bevel encoders not

aligned Align encoders

82

Contents

Main owner's manual MODEL NO. 113.197411 113.197511 SEARS /r.RRFT$IViRN 10-1NCH RADIALSAW assembly operating repair parts \ Y\ Sold by SEARS,ROEBUCK AND CO., Chicago, IL60684 U.S.A. Table of Contents Section Title .......................... Page 5. Burns. Safety Symbol and Signal Words _DANGER WARNING kWARNING Safety Instructions Safety Page On-Product Safety Labels ADANGERi kWARNING DANGER Identify Parts QJlIF*llfq!lt illIHIll[Llllllqqq lll l l slide arm (2) 5) % battery (1) battery cover (1) ]lHllLltlLllltllllltB spacer (2) (2) I Assembly Steps used. Page Page ! I % / / Page %"a'2', t'III J-Shaped \, \ / [ Page /\ g / Assembly 5. Put saw in location where it will be used. Page Page Page L Alignment and Adjustment Controls Miter Lock Frees table sections to allow fence changing Tells position of blade and arm attouch of a button Insert into on-off switch Remove after turning saw off See Digital Display Section Controls Rip l.ock F_nncti_ Controls CxmU_ Guard Guard Clamp Screw Pawls/Spreader Wing Nut Frees pawls/spreader to move up and down Alignment and Adjustment Steps / Page Page Alignment and Adjustment screws. Alignment and Adjustment Page / , Page Page Page Alignment and Adjustment F Complete Adjustments Error Messages NL _,A/RS/CRRFTSMRN [/' I Install Battery To Replace Battery I I"1 _I.U J. UI V! BEv U [ 1.U U.U Set Zero Reference Points For Bevel, Miter, and Elevation I O1 Set Zero Reference Point For In- Rip 1 Set Zero Reference Point For Out-Rip ! o..,, I U.U U ! Electrical Connections Motor Specifications O Power Supply ,_ WARNING Electrical Connections \ a2T ll Koown rouo Extension Cords Motor Protection & Reset Button Electrical Connections To Change Motor Voltage to 240 A.C. DANGER / Crosscutting Crosscutting Defined Crosscutting Safety CAUTION ,/Do not touch or move workpieces until blade has stopped spinning. Crosscuttin Crosscutting Making Crosscuts Crosscuttin Repetitive Crosscutting Crosscutting Hints Ripping Defined In-Rip and Out-Rip Positions Infeed and Outfeed Directions Infeed and outfeed refer to sides of the blade. Workpiece Positioning Push Sticks and Push Blocks Ripping Safety ,_DANGER ,_ WARNING ]Zi, DANGER WARNING WARNING Guard Nose Function Pawls and Spreader Function Ripping Set-up Procedure Making Rip Cuts Edging Ripping Hints Cutting Aides Push Sticks Fences Cutting Aides Featherboard Cutting Aides Straight Edge for Irregular Workpiece WARNING Accessories Accessories Safety Information for Edging Accessories Lower Blade Guard the blade is in its rearmost position and Accessories ,_ CAUTION WARNING: Accessories for this Saw General Information WARNING Cleaning Lubrication \ Page rn =L 'ckNu Troubleshooting Motor Problem Possible Cause(s) What to Do Page Troubleshooting Cutting Problem Saw Problem Possible Cause(s) Miler nol locked firmly Troubleshooting Electronics Problem Page MODEL NOS. 113.197411 AND 113.197511 AND 113.197611 / MODEL NOS. 113.197411 AND 113.197611 AND 113.197511 Page FIGURE 2- BASE AND COLUMN ASSEMBLY Page MODEL NOS. 113.197411 AND 113.197611 AND 113.197511 FIGURE 3 - YOKE AND MOTOR ASSEMBLY MODEL NOS. 113.197411 AND 113.197511 AND 113.197611 I MODEL NOS. 113.197411 AND 113.197611 AND 113,197511 FIGURE 4 - YOKE ASSEMBLY F815817 Page Page Page x_ FIGURE 7- FOOT ASSEMBLY -MODEL 113.197511 & 113.197611 FIGURE 8 Repairs Parts MODEL NOS. 113.197411, 113.197511 AND 113.197611 Page Repairs Parts FIGURE 9- CABINET ASSEMBLY FOR MODEL 113.197411 AND 113.197511 FIGURE 10 -DRAWER ASSEMBLIES 3", 6", 10" FOR MODEL 113.197611 FIGURE 11 - MOTOR ASSEMBLY / FIGURE 12 - GUARD ASSEMBLY Index /- owner's manual SERVICE MODEL NO. J J Sold by SEARS,ROEBUCK AND CO., Chicago, IL 60684 U.S.A.