Manuals / Brands / Power Tools / Saw / Sears / Power Tools / Saw

Sears 113.197411, 113.197511, 113.197611 Safety Symbol and Signal Words, _DANGER

1 104

Download 104 pages, 4.64 Mb

Safety

This manual has safety information and in-

structions to help users eliminate or

reduce the risk of accidents and injuries,

including:

1. Severe cuts, and loss of fingers or other

body parts due to contact with the blade

2. Eye impact injuries, and blindness, from

being hit by a thrown workpiece,

workpiece chips or pieces of blade

3. Bodily impact injuries, broken bones,

and internal organ damage from being hit

by a thrown work'piece

4. Shock or electrocution

5. Burns.

Safety Symbol and Signal Words

An exclamation mark inside a triangle is

the safety alert symbol.

It is used to draw attention to safety infor-

mation in the manual and on the saw. It is

followed by a signal word, DANGER,

WARNING, or CAUTION, which tells

the level of risk:

_h, DANGER: means if the safety infor-

mation is not followed someone will be

seriously injured or killed.

WARNING: mearks if the safety infor-

mation is not followed someone could be

seriously injured or killed.

_ CAUTION: means if the safety infor-

mation is not followed someone might be

injured.

Read and follow all safety information

and instructions.

Major Hazards

Three major hazards are associated with

using the radial arm saw for ripping. They

are outfeed zone hazard, kickback, and

wrong way feed.

This section only briefly explains these

hazards. Read the ripping and crosscut-

ting safety sections for more detailed ex-

planations of these and other hazards.

Outfeed Zone Hazard

_DANGER

If you reach around the blade to the out-

feed side when ripping, and try to hold

down or pull the workpiece through to

complete a cut, the rotational force of the

blade will pull your hand back into the

blade.

Fingers will be cut off.

Read and follow the information and in-

structions under ripping safety.

Contents

Main owner's manual MODEL NO. 113.197411 113.197511 SEARS /r.RRFT$IViRN 10-1NCH RADIALSAW assembly operating repair parts \ Y\ Sold by SEARS,ROEBUCK AND CO., Chicago, IL60684 U.S.A. Table of Contents Section Title .......................... Page 5. Burns. Safety Symbol and Signal Words _DANGER WARNING kWARNING Safety Instructions Safety Page On-Product Safety Labels ADANGERi kWARNING DANGER Identify Parts QJlIF*llfq!lt illIHIll[Llllllqqq lll l l slide arm (2) 5) % battery (1) battery cover (1) ]lHllLltlLllltllllltB spacer (2) (2) I Assembly Steps used. Page Page ! I % / / Page %"a'2', t'III J-Shaped \, \ / [ Page /\ g / Assembly 5. Put saw in location where it will be used. Page Page Page L Alignment and Adjustment Controls Miter Lock Frees table sections to allow fence changing Tells position of blade and arm attouch of a button Insert into on-off switch Remove after turning saw off See Digital Display Section Controls Rip l.ock F_nncti_ Controls CxmU_ Guard Guard Clamp Screw Pawls/Spreader Wing Nut Frees pawls/spreader to move up and down Alignment and Adjustment Steps / Page Page Alignment and Adjustment screws. Alignment and Adjustment Page / , Page Page Page Alignment and Adjustment F Complete Adjustments Error Messages NL _,A/RS/CRRFTSMRN [/' I Install Battery To Replace Battery I I"1 _I.U J. UI V! BEv U [ 1.U U.U Set Zero Reference Points For Bevel, Miter, and Elevation I O1 Set Zero Reference Point For In- Rip 1 Set Zero Reference Point For Out-Rip ! o..,, I U.U U ! Electrical Connections Motor Specifications O Power Supply ,_ WARNING Electrical Connections \ a2T ll Koown rouo Extension Cords Motor Protection & Reset Button Electrical Connections To Change Motor Voltage to 240 A.C. DANGER / Crosscutting Crosscutting Defined Crosscutting Safety CAUTION ,/Do not touch or move workpieces until blade has stopped spinning. Crosscuttin Crosscutting Making Crosscuts Crosscuttin Repetitive Crosscutting Crosscutting Hints Ripping Defined In-Rip and Out-Rip Positions Infeed and Outfeed Directions Infeed and outfeed refer to sides of the blade. Workpiece Positioning Push Sticks and Push Blocks Ripping Safety ,_DANGER ,_ WARNING ]Zi, DANGER WARNING WARNING Guard Nose Function Pawls and Spreader Function Ripping Set-up Procedure Making Rip Cuts Edging Ripping Hints Cutting Aides Push Sticks Fences Cutting Aides Featherboard Cutting Aides Straight Edge for Irregular Workpiece WARNING Accessories Accessories Safety Information for Edging Accessories Lower Blade Guard the blade is in its rearmost position and Accessories ,_ CAUTION WARNING: Accessories for this Saw General Information WARNING Cleaning Lubrication \ Page rn =L 'ckNu Troubleshooting Motor Problem Possible Cause(s) What to Do Page Troubleshooting Cutting Problem Saw Problem Possible Cause(s) Miler nol locked firmly Troubleshooting Electronics Problem Page MODEL NOS. 113.197411 AND 113.197511 AND 113.197611 / MODEL NOS. 113.197411 AND 113.197611 AND 113.197511 Page FIGURE 2- BASE AND COLUMN ASSEMBLY Page MODEL NOS. 113.197411 AND 113.197611 AND 113.197511 FIGURE 3 - YOKE AND MOTOR ASSEMBLY MODEL NOS. 113.197411 AND 113.197511 AND 113.197611 I MODEL NOS. 113.197411 AND 113.197611 AND 113,197511 FIGURE 4 - YOKE ASSEMBLY F815817 Page Page Page x_ FIGURE 7- FOOT ASSEMBLY -MODEL 113.197511 & 113.197611 FIGURE 8 Repairs Parts MODEL NOS. 113.197411, 113.197511 AND 113.197611 Page Repairs Parts FIGURE 9- CABINET ASSEMBLY FOR MODEL 113.197411 AND 113.197511 FIGURE 10 -DRAWER ASSEMBLIES 3", 6", 10" FOR MODEL 113.197611 FIGURE 11 - MOTOR ASSEMBLY / FIGURE 12 - GUARD ASSEMBLY Index /- owner's manual SERVICE MODEL NO. J J Sold by SEARS,ROEBUCK AND CO., Chicago, IL 60684 U.S.A.