Controls | Sears 113.197611, 113.197511, 113.197411 instruction

Controls

CxmU_

Guard

Guard Clamp

Screw

Pawls/Spreader

Wing Nut

Spreader Nut Pawls/Spreader

FunctionOperation/Comments

Guard

Guard Clamp Screw

Pawls/Spreader Wing Nut

Spreader Nut

Pawls/Spreader

Partially protects against blade contact; keeps workpiece from fluttering

during ripping; acts as saw- dust deflector

Frees guard to rotate about blade

Frees pawls/spreader to move up and down

Frees pawls/spreader to move side to side

Reduce kickback by keeping kerf open (spreader func- tion); slow or stop kickback by digging into workpiece (pawls function)

Lock in level position for crosscut; for ripping, rotate until guard nose just clears top surface of workpiece, then lock in place

See Ripping Set- Up for details and illustrations

Turn counterclockwise to loosen, clockwise to tighten

Turn counterclockwise to loosen, clockwise to tighten

Loosen to make adjustment, then tighten.

For safety reasons spreader must be in line with blade. See

Alignment: Spreader to Blade

Set as unit, so pawl is level on workpiece and spreader rides in kerr. For safety reasons set

pawls/spreader before ripping,.

See Ripping Set- Up for details and illustrations

36

Image 36

Sears 113.197611, 113.197511, 113.197411 owner manual Controls

Contents

113.197511 113.197611Part No. SP5539 Contents Safety Safety Symbol and Signal WordsMajor Hazards KWARNING Wrong Way Feed Hazard Safety Instructions Personal Safety InstructionsWork Area Safety Instructions Saw Safety Instructions Workpiece Safety Instructions Blade Safety Instructions On-Product Safety Labels KWARNING Safety Assembly Identify Parts QJlIF*llfq!lt LHllLltlLllltllllltB Tools Needed For Assembly Assembly Steps Build Cabinet Base Build Foot Assemblies Shaped Slot Attach Foot Assemblies Short Assemble Side PanelsOnly Door Model without Casters Assembly Attach Door Hinges Attach/Install Spacers Attach Side Panels to Bottom Shelf Attach Skirts Center Support Upper Lower Complete Center Slide Assembly Attach DoorsOnly Drawer Model Center Support Assemble Drawers Attach Handwheel Mount Motor Shaft has left-hand threa&. Turn nut clock- wise to loosen Assembly Mount Basic Saw Assembly Adjust Leveling Feet Attach Trim Caps Install Front Table Attach Slide Arm Supports Clips. Note Table will extend about Beyond Trim caps Assemble Table Lock Mechanism Alignment and Adjustment Install Drawers Only Drawer ModelTo Remove Drawers Only Drawer Model Controls 45, -45 , 90 Rip l.ock Controls Alignment and Adjustment Alignment and Adjustment StepsAdjust Column Support Level Front Table Square Crosscut Travel Install Blade Square Blade to Table for Crosscut- ting Alignment and Adjustment Square Blade to Fence Square Blade to Table for Ripping Adjust Carriage Bearings Make Blade Parallel to Table Install Guard Align Spreader to Blade Complete Adjustments Go to Digital Display Section and follow Error Messages Digital DisplayButton Functions =73 Install Battery To Replace Battery Align Encoders Miter Encoder Set Zero Reference Points For Bevel, Miter, and Elevation Bevel Encoder Set Zero Reference Point For Rip Set Zero Reference Point For Out-Rip Conversion Table Motor Specifications Power Supply Motor Protection & Reset Button Electrical Connections To Change Motor Voltage to 240 A.C To avoid electric shock, unplug sawBefore changing Motor voltage Crosscutting Safety CrosscuttingDuring crosscutting, blade teeth can Having fingers, hand or arm cut off Crosscuttin Crosscut Kerfs Making Crosscuts Step Repetitive Crosscutting Ripping Ripping DefinedIn-Rip and Out-Rip Positions Infeed and Outfeed Directions Ripping Safety Workpiece Positioning Kickback Pinching or binding can happen when Ripping Wrong Way Feed Guard Nose Function Pawls and Spreader Function Ripping Set-up Procedure If workpiece is pushed along fenceWith kerfs, workpiece could get Making Rip Cuts Inleed Ripping Hints Dado Blades, Molding Heads Cutting Aides FencesPush Sticks Auxiliary Fence and Push Block for Ripping Cutting Aides Cutting Aides Straight Edge for Irregular Workpiece Accessories Safety Information for DadoInformation for Edging Lower Blade Guard Edging without an auxiliary fence Accessories Lower blade guard can get caught orJam in fence or table kerfs Maintenance CleaningGeneral Information Lubrication Adjustments for Wear Remove screw and nut from swivel lock knob Carriage Bearings Arm and Column Blade Changing Replacing Pawls Motor Problem Possible CausesWhat to Do Troubleshooting Troubleshooting Cutting ProblemSaw Problem Possible Causes Troubleshooting Electronics Problem Blank Repair Parts Model NOS .197411 and 113.197511 Repair Parts Always order by Part Number Not by Key Number Model NOS .197411 and 113.197611 Base and Column Assembly Model NOS .197411 and 113.197511 Parts List for Craftsman 10 Electronic Radial SAW Model NOS .197411 and 113.197611 Model NOS .197411 and 113.197511 Model NOS .197411 and 113.197611 and 113,197511 Part Repair Parts ARM Assembly Table Assembly Foot Assembly Model 113.197511 Model NOS .197411, 113.197511 Repairs Parts Model NOS .197411, 113.197511 Repairs Parts Cabinet Assembly for Model 113.197411 For Model Motor Assembly Guard Assembly Index Sold by SEARS, Roebuck and CO., Chicago, IL 60684 U.S.A 113.197411Pail No. SP5539