Manuals / Sears / Power Tools / Saw

Sears 113.197611, 113.197511 Troubleshooting, Cutting Problem, Saw Problem, Possible Causes

Models: 113.197411 113.197511 113.197611

1 104

Download 104 pages 10.3 Kb

Page 81

Image 81

Troubleshooting

Cutting Problem

Workpiece strikes spreader during ripping

Workpiece binds, smokes, and motor slows or stops when ripping

Board pulls away from fence during ripping

Possible Cause(s)

Spreader not in line with blade

Saw blade out of alignment

Warped workpiece

Feed rate too fast

Carriage assembly loose

Fence not straight

Dull or incorrect blade

Blade out of alignment

May occur as normal result of ap- plying feed pressure

What to Do

Align spreader to blade

Re-align

Do not cut severely warped pieces Slow feed rate

Adjust carriage bearings, then re- align saw

Replace fence

Sharpen or replace blade

Re-align

Use featherboard on infeed side

Saw Problem

Radial arm moves when locked in a non-indexed miter position

Motor moves when bevel lock is locked

Blade carriage moves when rip lock is locked

Blade carriage does not travel smoothly on arm

Possible Cause(s)

Miler nol locked firmly

Bevel not locked firmly

Rip lock not locked firmly

Dirty track

Carriage bearing set too tight

Rip lock too tight

Worn arm track

Bad carriage bearing

What to do

Adjust miter lock for wear

Adjust bevel lock for wear

Adjust rip lock for wear

CIean and lubricate track

Adjust carriage bearings, then re- align saw

Adjust rip lock

Have Sears replace arm track

Replace carriage bearing

Blade does not stop spinning	Blade nut loose
wilhin 15 seconds after saw is
turned off	Internal damage

Tighten blade nut

Take saw back to Sears for service

81

Image 81

Sears 113.197611, 113.197511, 113.197411 owner manual Troubleshooting, Cutting Problem, Saw Problem, Possible Causes

Contents

113.197511 113.197611Part No. SP5539 Contents Safety Safety Symbol and Signal WordsMajor Hazards Wrong Way Feed Hazard KWARNING Safety Instructions Personal Safety InstructionsWork Area Safety Instructions Workpiece Safety Instructions Saw Safety Instructions Blade Safety Instructions KWARNING On-Product Safety Labels Safety Identify Parts Assembly QJlIF*llfq!lt LHllLltlLllltllllltB Tools Needed For Assembly Build Cabinet Base Assembly Steps Build Foot Assemblies Shaped Slot Attach Foot Assemblies Short Assemble Side PanelsOnly Door Model without Casters Attach Door Hinges Assembly Attach Side Panels to Bottom Shelf Attach/Install Spacers Attach Skirts Center Support Upper Lower Complete Center Slide Assembly Attach DoorsOnly Drawer Model Center Support Attach Handwheel Assemble Drawers Shaft has left-hand threa&. Turn nut clock- wise to loosen Mount Motor Mount Basic Saw Assembly Assembly Attach Trim Caps Adjust Leveling Feet Attach Slide Arm Supports Install Front Table Clips. Note Table will extend about Beyond Trim caps Assemble Table Lock Mechanism Alignment and Adjustment Install Drawers Only Drawer ModelTo Remove Drawers Only Drawer Model 45, -45 , 90 Controls Rip l.ock Controls Alignment and Adjustment Alignment and Adjustment StepsAdjust Column Support Level Front Table Square Crosscut Travel Square Blade to Table for Crosscut- ting Install Blade Alignment and Adjustment Square Blade to Fence Square Blade to Table for Ripping Adjust Carriage Bearings Make Blade Parallel to Table Align Spreader to Blade Install Guard Go to Digital Display Section and follow Complete Adjustments Digital Display Error MessagesButton Functions =73 To Replace Battery Install Battery Miter Encoder Align Encoders Bevel Encoder Set Zero Reference Points For Bevel, Miter, and Elevation Set Zero Reference Point For Out-Rip Set Zero Reference Point For Rip Conversion Table Power Supply Motor Specifications Electrical Connections Motor Protection & Reset Button To Change Motor Voltage to 240 A.C To avoid electric shock, unplug sawBefore changing Motor voltage Crosscutting Crosscutting SafetyDuring crosscutting, blade teeth can Having fingers, hand or arm cut off Crosscut Kerfs Crosscuttin Step Making Crosscuts Repetitive Crosscutting Ripping Defined RippingIn-Rip and Out-Rip Positions Infeed and Outfeed Directions Workpiece Positioning Ripping Safety Pinching or binding can happen when Kickback Wrong Way Feed Ripping Pawls and Spreader Function Guard Nose Function Ripping Set-up Procedure If workpiece is pushed along fenceWith kerfs, workpiece could get Inleed Making Rip Cuts Dado Blades, Molding Heads Ripping Hints Fences Cutting AidesPush Sticks Auxiliary Fence and Push Block for Ripping Cutting Aides Straight Edge for Irregular Workpiece Cutting Aides Accessories Safety Information for DadoInformation for Edging Edging without an auxiliary fence Lower Blade Guard Accessories Lower blade guard can get caught orJam in fence or table kerfs Cleaning MaintenanceGeneral Information Lubrication Remove screw and nut from swivel lock knob Adjustments for Wear Arm and Column Carriage Bearings Replacing Pawls Blade Changing Motor Problem Possible CausesWhat to Do Troubleshooting Cutting Problem TroubleshootingSaw Problem Possible Causes Electronics Problem Troubleshooting Blank Model NOS .197411 and 113.197511 Repair Parts Always order by Part Number Not by Key Number Repair Parts Model NOS .197411 and 113.197611 Base and Column Assembly Model NOS .197411 and 113.197511 Model NOS .197411 and 113.197611 Parts List for Craftsman 10 Electronic Radial SAW Model NOS .197411 and 113.197511 Part Model NOS .197411 and 113.197611 and 113,197511 Repair Parts ARM Assembly Table Assembly Foot Assembly Model 113.197511 Model NOS .197411, 113.197511 Model NOS .197411, 113.197511 Repairs Parts Repairs Parts Cabinet Assembly for Model 113.197411 Model For Motor Assembly Guard Assembly Index Sold by SEARS, Roebuck and CO., Chicago, IL 60684 U.S.A 113.197411Pail No. SP5539