Shaped Slot | Sears 113.197511, 113.197611, 113.197411 instruction

Assembly

2.Place one foot box so C-shaped open- ing faces you and closed side is on your left.

3.With threaded end of foot rod facing down, and smaller square opening facing you, put rod through top opening of foot box, and slide half way down into box.

4.Put grooved pin through hole in foot rod so grooved end faces out.

5.On end of foot rod put washer then spring. Push rod all the way down through spring.

6.With lever pointing towards left, put foot lever through upper opening of "C", through rod, and out other end of foot

box. Apply a few drops of SAE 10W-30 motor oil to area where lever and rod

meet.

7.Put smooth pin through hole at end of foot lever.

C-Shaped

Slot

Rod

Smaller Square

Opening

Grooved Pin

Washer And

Spring

Rod

Lever Points

Toward Left

Smooth Pin

16

Image 16

Sears 113.197511, 113.197611, 113.197411 owner manual Shaped Slot

Contents

113.197611 113.197511Part No. SP5539 Contents Safety Symbol and Signal Words SafetyMajor Hazards KWARNING Wrong Way Feed Hazard Personal Safety Instructions Safety InstructionsWork Area Safety Instructions Saw Safety Instructions Workpiece Safety Instructions Blade Safety Instructions On-Product Safety Labels KWARNING Safety Assembly Identify Parts QJlIF*llfq!lt LHllLltlLllltllllltB Tools Needed For Assembly Assembly Steps Build Cabinet Base Build Foot Assemblies Shaped Slot Attach Foot Assemblies Short Assemble Side PanelsOnly Door Model without Casters Assembly Attach Door Hinges Attach/Install Spacers Attach Side Panels to Bottom Shelf Attach Skirts Center Support Upper Lower Attach Doors Complete Center Slide AssemblyOnly Drawer Model Center Support Assemble Drawers Attach Handwheel Mount Motor Shaft has left-hand threa&. Turn nut clock- wise to loosen Assembly Mount Basic Saw Assembly Adjust Leveling Feet Attach Trim Caps Install Front Table Attach Slide Arm Supports Clips. Note Table will extend about Beyond Trim caps Assemble Table Lock Mechanism Install Drawers Only Drawer Model Alignment and AdjustmentTo Remove Drawers Only Drawer Model Controls 45, -45 , 90 Rip l.ock Controls Alignment and Adjustment Steps Alignment and AdjustmentAdjust Column Support Level Front Table Square Crosscut Travel Install Blade Square Blade to Table for Crosscut- ting Alignment and Adjustment Square Blade to Fence Square Blade to Table for Ripping Adjust Carriage Bearings Make Blade Parallel to Table Install Guard Align Spreader to Blade Complete Adjustments Go to Digital Display Section and follow Error Messages Digital DisplayButton Functions =73 Install Battery To Replace Battery Align Encoders Miter Encoder Set Zero Reference Points For Bevel, Miter, and Elevation Bevel Encoder Set Zero Reference Point For Rip Set Zero Reference Point For Out-Rip Conversion Table Motor Specifications Power Supply Motor Protection & Reset Button Electrical Connections To avoid electric shock, unplug saw To Change Motor Voltage to 240 A.CBefore changing Motor voltage Crosscutting Safety CrosscuttingDuring crosscutting, blade teeth can Having fingers, hand or arm cut off Crosscuttin Crosscut Kerfs Making Crosscuts Step Repetitive Crosscutting Ripping Ripping DefinedIn-Rip and Out-Rip Positions Infeed and Outfeed Directions Ripping Safety Workpiece Positioning Kickback Pinching or binding can happen when Ripping Wrong Way Feed Guard Nose Function Pawls and Spreader Function If workpiece is pushed along fence Ripping Set-up ProcedureWith kerfs, workpiece could get Making Rip Cuts Inleed Ripping Hints Dado Blades, Molding Heads Cutting Aides FencesPush Sticks Auxiliary Fence and Push Block for Ripping Cutting Aides Cutting Aides Straight Edge for Irregular Workpiece Information for Dado Accessories SafetyInformation for Edging Lower Blade Guard Edging without an auxiliary fence Lower blade guard can get caught or AccessoriesJam in fence or table kerfs Maintenance CleaningGeneral Information Lubrication Adjustments for Wear Remove screw and nut from swivel lock knob Carriage Bearings Arm and Column Blade Changing Replacing Pawls Possible Causes Motor ProblemWhat to Do Troubleshooting Troubleshooting Cutting ProblemSaw Problem Possible Causes Troubleshooting Electronics Problem Blank Repair Parts Model NOS .197411 and 113.197511 Repair Parts Always order by Part Number Not by Key Number Model NOS .197411 and 113.197611 Base and Column Assembly Model NOS .197411 and 113.197511 Parts List for Craftsman 10 Electronic Radial SAW Model NOS .197411 and 113.197611 Model NOS .197411 and 113.197511 Model NOS .197411 and 113.197611 and 113,197511 Part Repair Parts ARM Assembly Table Assembly Foot Assembly Model 113.197511 Model NOS .197411, 113.197511 Repairs Parts Model NOS .197411, 113.197511 Repairs Parts Cabinet Assembly for Model 113.197411 For Model Motor Assembly Guard Assembly Index 113.197411 Sold by SEARS, Roebuck and CO., Chicago, IL 60684 U.S.APail No. SP5539