Manuals / Brands / Power Tools / Saw / Sears / Power Tools / Saw

Sears 113.197411, 113.197511, 113.197611 rn =L 'ckNu

1 104

Download 104 pages, 4.64 Mb

Maintenance

Rip Lock

If the blade carriage can be moved by

pushing/pulling on the saw handle when

the rip lock is locked, adjust:

1.Hold rip lock in unlocked position and

tighten locknut one quarter turn.

2. Test adjustment: if carriage moves with

difficulty, slightly loosen locknut; if car-

riage moves easily, lock rip lock and try

to move carriage along arm.

Replacing Pawls

Make sure the teeth of the pawls are al-

ways sharp. If they become dull the pawls

must be replaced:

1. Remove hex nut and old pawls.

2. Install new pawls and spreader.

3. Align spreader to blade according to in-

structions in Alignment and Adjustment.

Blade Changing

To change the saw blade:

1. Turn switch off, remove yellow key,

and unplug saw.

2. Use both blade wrenches in scissor ac-

tion to loosen blade nut. Note:Arbor

shaft hc** left-hand thread_. Turn nut clock-

wise to loosen.

3. Remove nut, blade collar, and blade.

Insert new blade, making sure that arrow

is on outside and points clockwise.

4. Re-install blade collar and nut. Note:

Do not overtighten nut because this can

cause blade collar to warp and blade to

wobble during cutting:

£rn =L 'ckNu

Rip-Lock Cam \

Level Carriage Bolt

78

Contents

Main owner's manual MODEL NO. 113.197411 113.197511 SEARS /r.RRFT$IViRN 10-1NCH RADIALSAW assembly operating repair parts \ Y\ Sold by SEARS,ROEBUCK AND CO., Chicago, IL60684 U.S.A. Table of Contents Section Title .......................... Page 5. Burns. Safety Symbol and Signal Words _DANGER WARNING kWARNING Safety Instructions Safety Page On-Product Safety Labels ADANGERi kWARNING DANGER Identify Parts QJlIF*llfq!lt illIHIll[Llllllqqq lll l l slide arm (2) 5) % battery (1) battery cover (1) ]lHllLltlLllltllllltB spacer (2) (2) I Assembly Steps used. Page Page ! I % / / Page %"a'2', t'III J-Shaped \, \ / [ Page /\ g / Assembly 5. Put saw in location where it will be used. Page Page Page L Alignment and Adjustment Controls Miter Lock Frees table sections to allow fence changing Tells position of blade and arm attouch of a button Insert into on-off switch Remove after turning saw off See Digital Display Section Controls Rip l.ock F_nncti_ Controls CxmU_ Guard Guard Clamp Screw Pawls/Spreader Wing Nut Frees pawls/spreader to move up and down Alignment and Adjustment Steps / Page Page Alignment and Adjustment screws. Alignment and Adjustment Page / , Page Page Page Alignment and Adjustment F Complete Adjustments Error Messages NL _,A/RS/CRRFTSMRN [/' I Install Battery To Replace Battery I I"1 _I.U J. UI V! BEv U [ 1.U U.U Set Zero Reference Points For Bevel, Miter, and Elevation I O1 Set Zero Reference Point For In- Rip 1 Set Zero Reference Point For Out-Rip ! o..,, I U.U U ! Electrical Connections Motor Specifications O Power Supply ,_ WARNING Electrical Connections \ a2T ll Koown rouo Extension Cords Motor Protection & Reset Button Electrical Connections To Change Motor Voltage to 240 A.C. DANGER / Crosscutting Crosscutting Defined Crosscutting Safety CAUTION ,/Do not touch or move workpieces until blade has stopped spinning. Crosscuttin Crosscutting Making Crosscuts Crosscuttin Repetitive Crosscutting Crosscutting Hints Ripping Defined In-Rip and Out-Rip Positions Infeed and Outfeed Directions Infeed and outfeed refer to sides of the blade. Workpiece Positioning Push Sticks and Push Blocks Ripping Safety ,_DANGER ,_ WARNING ]Zi, DANGER WARNING WARNING Guard Nose Function Pawls and Spreader Function Ripping Set-up Procedure Making Rip Cuts Edging Ripping Hints Cutting Aides Push Sticks Fences Cutting Aides Featherboard Cutting Aides Straight Edge for Irregular Workpiece WARNING Accessories Accessories Safety Information for Edging Accessories Lower Blade Guard the blade is in its rearmost position and Accessories ,_ CAUTION WARNING: Accessories for this Saw General Information WARNING Cleaning Lubrication \ Page rn =L 'ckNu Troubleshooting Motor Problem Possible Cause(s) What to Do Page Troubleshooting Cutting Problem Saw Problem Possible Cause(s) Miler nol locked firmly Troubleshooting Electronics Problem Page MODEL NOS. 113.197411 AND 113.197511 AND 113.197611 / MODEL NOS. 113.197411 AND 113.197611 AND 113.197511 Page FIGURE 2- BASE AND COLUMN ASSEMBLY Page MODEL NOS. 113.197411 AND 113.197611 AND 113.197511 FIGURE 3 - YOKE AND MOTOR ASSEMBLY MODEL NOS. 113.197411 AND 113.197511 AND 113.197611 I MODEL NOS. 113.197411 AND 113.197611 AND 113,197511 FIGURE 4 - YOKE ASSEMBLY F815817 Page Page Page x_ FIGURE 7- FOOT ASSEMBLY -MODEL 113.197511 & 113.197611 FIGURE 8 Repairs Parts MODEL NOS. 113.197411, 113.197511 AND 113.197611 Page Repairs Parts FIGURE 9- CABINET ASSEMBLY FOR MODEL 113.197411 AND 113.197511 FIGURE 10 -DRAWER ASSEMBLIES 3", 6", 10" FOR MODEL 113.197611 FIGURE 11 - MOTOR ASSEMBLY / FIGURE 12 - GUARD ASSEMBLY Index /- owner's manual SERVICE MODEL NO. J J Sold by SEARS,ROEBUCK AND CO., Chicago, IL 60684 U.S.A.