Manuals / Sears / Power Tools / Saw

Sears 113.197411, 113.197611, 113.197511 Cutting Aides, Straight Edge for Irregular Workpiece

Models: 113.197411 113.197511 113.197611

1 104

Download 104 pages 10.3 Kb

Page 71

Cutting Aides

Clamp the featherboard to the front table, so that the angled edge of the feather-

board is against the workpiece on the in- feed side of the blade. Do not clamp the

featherboard against the cut off part (out-

feed side) of the workpiece. If clamped to

the outfeed side, the featherboard can squeeze the kerr closed, put binding pres- sure on the blade, and cause kickback.

Feather Board

This Side

Straight Edge for Irregular

Workpiece

WARNING

If you try to rip an irregular workpiece, it could bind blade and cause kickback.

If the workpiece you want to rip does not have a straight edge, attach a straight- edged board to the workpiece:

i)place irregular side of workpiece against fence

ii)put straight-edged board on top of workpiece and against fence

iii)tack straight edged board to workpiece.

Note: Straight-edged board must not extend

beyond leading end of workpiece and

should cover workpiece width only enough to pass between blade and fence.

Note: Use fence at least at high as com-

bined heights of workpiece and straight- edged board.

71

Image 71

Sears 113.197411, 113.197611, 113.197511 owner manual Cutting Aides, Straight Edge for Irregular Workpiece

Contents

Part No. SP5539 113.197511113.197611 Contents Major Hazards SafetySafety Symbol and Signal Words Wrong Way Feed Hazard KWARNING Work Area Safety Instructions Safety InstructionsPersonal Safety Instructions Workpiece Safety Instructions Saw Safety Instructions Blade Safety Instructions KWARNING On-Product Safety Labels Safety Identify Parts Assembly QJlIF*llfq!lt LHllLltlLllltllllltB Tools Needed For Assembly Build Cabinet Base Assembly Steps Build Foot Assemblies Shaped Slot Attach Foot Assemblies Short Assemble Side PanelsOnly Door Model without Casters Attach Door Hinges Assembly Attach Side Panels to Bottom Shelf Attach/Install Spacers Attach Skirts Center Support Upper Lower Only Drawer Model Complete Center Slide AssemblyAttach Doors Center Support Attach Handwheel Assemble Drawers Shaft has left-hand threa&. Turn nut clock- wise to loosen Mount Motor Mount Basic Saw Assembly Assembly Attach Trim Caps Adjust Leveling Feet Attach Slide Arm Supports Install Front Table Clips. Note Table will extend about Beyond Trim caps Assemble Table Lock Mechanism To Remove Drawers Only Drawer Model Alignment and AdjustmentInstall Drawers Only Drawer Model 45, -45 , 90 Controls Rip l.ock Controls Adjust Column Support Alignment and AdjustmentAlignment and Adjustment Steps Level Front Table Square Crosscut Travel Square Blade to Table for Crosscut- ting Install Blade Alignment and Adjustment Square Blade to Fence Square Blade to Table for Ripping Adjust Carriage Bearings Make Blade Parallel to Table Align Spreader to Blade Install Guard Go to Digital Display Section and follow Complete Adjustments =73 Error MessagesDigital Display Button Functions To Replace Battery Install Battery Miter Encoder Align Encoders Bevel Encoder Set Zero Reference Points For Bevel, Miter, and Elevation Set Zero Reference Point For Out-Rip Set Zero Reference Point For Rip Conversion Table Power Supply Motor Specifications Electrical Connections Motor Protection & Reset Button Before changing Motor voltage To Change Motor Voltage to 240 A.CTo avoid electric shock, unplug saw Having fingers, hand or arm cut off Crosscutting SafetyCrosscutting During crosscutting, blade teeth can Crosscut Kerfs Crosscuttin Step Making Crosscuts Repetitive Crosscutting Infeed and Outfeed Directions RippingRipping Defined In-Rip and Out-Rip Positions Workpiece Positioning Ripping Safety Pinching or binding can happen when Kickback Wrong Way Feed Ripping Pawls and Spreader Function Guard Nose Function With kerfs, workpiece could get Ripping Set-up ProcedureIf workpiece is pushed along fence Inleed Making Rip Cuts Dado Blades, Molding Heads Ripping Hints Auxiliary Fence and Push Block for Ripping Cutting AidesFences Push Sticks Cutting Aides Straight Edge for Irregular Workpiece Cutting Aides Information for Edging Accessories SafetyInformation for Dado Edging without an auxiliary fence Lower Blade Guard Jam in fence or table kerfs AccessoriesLower blade guard can get caught or Lubrication MaintenanceCleaning General Information Remove screw and nut from swivel lock knob Adjustments for Wear Arm and Column Carriage Bearings Replacing Pawls Blade Changing What to Do Motor ProblemPossible Causes Troubleshooting Possible Causes TroubleshootingCutting Problem Saw Problem Electronics Problem Troubleshooting Blank Model NOS .197411 and 113.197511 Repair Parts Always order by Part Number Not by Key Number Repair Parts Model NOS .197411 and 113.197611 Base and Column Assembly Model NOS .197411 and 113.197511 Model NOS .197411 and 113.197611 Parts List for Craftsman 10 Electronic Radial SAW Model NOS .197411 and 113.197511 Part Model NOS .197411 and 113.197611 and 113,197511 Repair Parts ARM Assembly Table Assembly Foot Assembly Model 113.197511 Model NOS .197411, 113.197511 Model NOS .197411, 113.197511 Repairs Parts Repairs Parts Cabinet Assembly for Model 113.197411 Model For Motor Assembly Guard Assembly Index Pail No. SP5539 Sold by SEARS, Roebuck and CO., Chicago, IL 60684 U.S.A113.197411