Manuals / Sears / Power Tools / Saw

Sears 113.197411, 113.197611, 113.197511 owner manual Adjust Leveling Feet, Attach Trim Caps

Models: 113.197411 113.197511 113.197611

1 104

Download 104 pages 10.3 Kb

Page 29

Adjust Leveling Feet

Note: If cabinet has casters; lock foot as- semblies and make sure front cm'ters are slightly off floor before adjusting leveling feet.

1.It"cabinet rocks, adjust leveling feet so they rest on floor.

2.Rest a level on radial arm. If arm is

level or slants forward, adjust leveling feet so arm slants slightly towards rear.

3.Only Door Model Without Casters: wrench tighten top nut on each leveling foot.

Attach Trim Caps

1.Line up plastic stubs on back of trim caps with holes on front corners of frame and snap into place.

Attach Lock Handle Channels

1. Set out:

-two lock handle channels -two lock handles

-four v4" diam x lvs" long pan head screws -four 1/4"diam lock washers

-four va" diam hex nuts.

2.Insert lock handles through openings in front of saw.

3.Slide lock handle channel, open side facing down, onto each lock handle and attach: use two screws per channel (hzsert

screws through lock handle channel); on end of each screw put washer, then nut and wrench tighten.

Assembly

_, WARNING

Saw must slant slightly towards rear to keep blade carriage from rolling

forward. Workpiece or saw can move unexpectedly if cabinet rocks. Fingers, hand or arm could be cut off by blade contact.

Adjust leveling feet before using

saw.

Trim Cap

\

29

Image 29

Sears 113.197411, 113.197611, 113.197511 owner manual Adjust Leveling Feet, Attach Trim Caps

Contents

Part No. SP5539 113.197511113.197611 Contents Major Hazards SafetySafety Symbol and Signal Words Wrong Way Feed Hazard KWARNING Work Area Safety Instructions Safety InstructionsPersonal Safety Instructions Workpiece Safety Instructions Saw Safety Instructions Blade Safety Instructions KWARNING On-Product Safety Labels Safety Identify Parts Assembly QJlIF*llfq!lt LHllLltlLllltllllltB Tools Needed For Assembly Build Cabinet Base Assembly Steps Build Foot Assemblies Shaped Slot Attach Foot Assemblies Short Assemble Side PanelsOnly Door Model without Casters Attach Door Hinges Assembly Attach Side Panels to Bottom Shelf Attach/Install Spacers Attach Skirts Center Support Upper Lower Only Drawer Model Complete Center Slide AssemblyAttach Doors Center Support Attach Handwheel Assemble Drawers Shaft has left-hand threa&. Turn nut clock- wise to loosen Mount Motor Mount Basic Saw Assembly Assembly Attach Trim Caps Adjust Leveling Feet Attach Slide Arm Supports Install Front Table Clips. Note Table will extend about Beyond Trim caps Assemble Table Lock Mechanism To Remove Drawers Only Drawer Model Alignment and AdjustmentInstall Drawers Only Drawer Model 45, -45 , 90 Controls Rip l.ock Controls Adjust Column Support Alignment and AdjustmentAlignment and Adjustment Steps Level Front Table Square Crosscut Travel Square Blade to Table for Crosscut- ting Install Blade Alignment and Adjustment Square Blade to Fence Square Blade to Table for Ripping Adjust Carriage Bearings Make Blade Parallel to Table Align Spreader to Blade Install Guard Go to Digital Display Section and follow Complete Adjustments Digital Display Error MessagesButton Functions =73 To Replace Battery Install Battery Miter Encoder Align Encoders Bevel Encoder Set Zero Reference Points For Bevel, Miter, and Elevation Set Zero Reference Point For Out-Rip Set Zero Reference Point For Rip Conversion Table Power Supply Motor Specifications Electrical Connections Motor Protection & Reset Button Before changing Motor voltage To Change Motor Voltage to 240 A.CTo avoid electric shock, unplug saw Crosscutting Crosscutting SafetyDuring crosscutting, blade teeth can Having fingers, hand or arm cut off Crosscut Kerfs Crosscuttin Step Making Crosscuts Repetitive Crosscutting Ripping Defined RippingIn-Rip and Out-Rip Positions Infeed and Outfeed Directions Workpiece Positioning Ripping Safety Pinching or binding can happen when Kickback Wrong Way Feed Ripping Pawls and Spreader Function Guard Nose Function With kerfs, workpiece could get Ripping Set-up ProcedureIf workpiece is pushed along fence Inleed Making Rip Cuts Dado Blades, Molding Heads Ripping Hints Fences Cutting AidesPush Sticks Auxiliary Fence and Push Block for Ripping Cutting Aides Straight Edge for Irregular Workpiece Cutting Aides Information for Edging Accessories SafetyInformation for Dado Edging without an auxiliary fence Lower Blade Guard Jam in fence or table kerfs AccessoriesLower blade guard can get caught or Cleaning MaintenanceGeneral Information Lubrication Remove screw and nut from swivel lock knob Adjustments for Wear Arm and Column Carriage Bearings Replacing Pawls Blade Changing What to Do Motor ProblemPossible Causes Troubleshooting Cutting Problem TroubleshootingSaw Problem Possible Causes Electronics Problem Troubleshooting Blank Model NOS .197411 and 113.197511 Repair Parts Always order by Part Number Not by Key Number Repair Parts Model NOS .197411 and 113.197611 Base and Column Assembly Model NOS .197411 and 113.197511 Model NOS .197411 and 113.197611 Parts List for Craftsman 10 Electronic Radial SAW Model NOS .197411 and 113.197511 Part Model NOS .197411 and 113.197611 and 113,197511 Repair Parts ARM Assembly Table Assembly Foot Assembly Model 113.197511 Model NOS .197411, 113.197511 Model NOS .197411, 113.197511 Repairs Parts Repairs Parts Cabinet Assembly for Model 113.197411 Model For Motor Assembly Guard Assembly Index Pail No. SP5539 Sold by SEARS, Roebuck and CO., Chicago, IL 60684 U.S.A113.197411