Manuals / Brands / Power Tools / Saw / Sears / Power Tools / Saw

Sears 113.197411, 113.197511, 113.197611 Crosscutting

1 104

Download 104 pages, 4.64 Mb

Crosscutting

Crosscutting Defined

Crosscutting is cutting a workpiece to

length. The workpiece is held firmly

against the fence, and the blade is pulled

through the workpiece to make the cut.

Straight, bevel, miter and compound cuts

can be made.

Crosscutting Safety

The hazards associated with crosscutting

include: exposed blade teeth, rolling car-

riage, and thrown workpiece. This section

explains these hazards and tells how to

avoid them or reduce the risk of their hap-

pening. Read this section before making

any type of crosscut. Follow these steps

every, time you make a crosscut.

Exposed Blade Teeth

WARNING

During crosscutting, blade teeth can

be exposed. To reduce risk of

having fingers, hand or arm cut off:

_/Set bottom edge of guard parallel to

table to cover upper half of blade.

,/Lower pawls to clear fence or

workpiece, whichever is higher, by va".

Ix)wered pawls act as partial barrier to

front of blade.

`/Keep hands away from blade and out

of blade path. Keep hand holding down

workpiece at least 8" from blade.

,/ Blade can come off table edge beyond

30° left miter position. Use right miter

position whenever possible.

v_Do not cut freehand. You will not be

able to control workpiece.

,/If blade jams, turn off saw, remove yel-

low key, then free blade.

Straight Bevel

Miter

Compound

Rolling Carriage

_, WARNING

When saw is turned on, blade can

suddenly come forward. To reduce

risk of this happening:

`/Keep one hand on saw handle when

turning saw on.

_;Adjust leveling feet to make sure

radial arm slants slightly toward rear.

Thrown Workpiece

CAUTION

Workpiece could be picked up by

spinning blade and thrown. You

might be hit by thrown workpiece.

To reduce risk of thrown workpiece:

`/Make sure installed fence is at least

half as high as the workpiece, and

never less than 3/4".

v' Start and finish cut with blade in rear-

most position, behind fence.

,1'Firmly hold workpiece flat on table

and up against fence. Cut only one

workpiece at atime.

`/Pull blade through workpiece only dis-

tance needed to complete cut, and

never more than half diameter of blade.

,/Do not touch or move workpieces

until blade has stopped spinning.

,/Use length stop only on end of

workpiece which is held down.

`/Use table extensions t<) support

workpieces that extend beyond table.

57

Contents

Main owner's manual MODEL NO. 113.197411 113.197511 SEARS /r.RRFT$IViRN 10-1NCH RADIALSAW assembly operating repair parts \ Y\ Sold by SEARS,ROEBUCK AND CO., Chicago, IL60684 U.S.A. Table of Contents Section Title .......................... Page 5. Burns. Safety Symbol and Signal Words _DANGER WARNING kWARNING Safety Instructions Safety Page On-Product Safety Labels ADANGERi kWARNING DANGER Identify Parts QJlIF*llfq!lt illIHIll[Llllllqqq lll l l slide arm (2) 5) % battery (1) battery cover (1) ]lHllLltlLllltllllltB spacer (2) (2) I Assembly Steps used. Page Page ! I % / / Page %"a'2', t'III J-Shaped \, \ / [ Page /\ g / Assembly 5. Put saw in location where it will be used. Page Page Page L Alignment and Adjustment Controls Miter Lock Frees table sections to allow fence changing Tells position of blade and arm attouch of a button Insert into on-off switch Remove after turning saw off See Digital Display Section Controls Rip l.ock F_nncti_ Controls CxmU_ Guard Guard Clamp Screw Pawls/Spreader Wing Nut Frees pawls/spreader to move up and down Alignment and Adjustment Steps / Page Page Alignment and Adjustment screws. Alignment and Adjustment Page / , Page Page Page Alignment and Adjustment F Complete Adjustments Error Messages NL _,A/RS/CRRFTSMRN [/' I Install Battery To Replace Battery I I"1 _I.U J. UI V! BEv U [ 1.U U.U Set Zero Reference Points For Bevel, Miter, and Elevation I O1 Set Zero Reference Point For In- Rip 1 Set Zero Reference Point For Out-Rip ! o..,, I U.U U ! Electrical Connections Motor Specifications O Power Supply ,_ WARNING Electrical Connections \ a2T ll Koown rouo Extension Cords Motor Protection & Reset Button Electrical Connections To Change Motor Voltage to 240 A.C. DANGER / Crosscutting Crosscutting Defined Crosscutting Safety CAUTION ,/Do not touch or move workpieces until blade has stopped spinning. Crosscuttin Crosscutting Making Crosscuts Crosscuttin Repetitive Crosscutting Crosscutting Hints Ripping Defined In-Rip and Out-Rip Positions Infeed and Outfeed Directions Infeed and outfeed refer to sides of the blade. Workpiece Positioning Push Sticks and Push Blocks Ripping Safety ,_DANGER ,_ WARNING ]Zi, DANGER WARNING WARNING Guard Nose Function Pawls and Spreader Function Ripping Set-up Procedure Making Rip Cuts Edging Ripping Hints Cutting Aides Push Sticks Fences Cutting Aides Featherboard Cutting Aides Straight Edge for Irregular Workpiece WARNING Accessories Accessories Safety Information for Edging Accessories Lower Blade Guard the blade is in its rearmost position and Accessories ,_ CAUTION WARNING: Accessories for this Saw General Information WARNING Cleaning Lubrication \ Page rn =L 'ckNu Troubleshooting Motor Problem Possible Cause(s) What to Do Page Troubleshooting Cutting Problem Saw Problem Possible Cause(s) Miler nol locked firmly Troubleshooting Electronics Problem Page MODEL NOS. 113.197411 AND 113.197511 AND 113.197611 / MODEL NOS. 113.197411 AND 113.197611 AND 113.197511 Page FIGURE 2- BASE AND COLUMN ASSEMBLY Page MODEL NOS. 113.197411 AND 113.197611 AND 113.197511 FIGURE 3 - YOKE AND MOTOR ASSEMBLY MODEL NOS. 113.197411 AND 113.197511 AND 113.197611 I MODEL NOS. 113.197411 AND 113.197611 AND 113,197511 FIGURE 4 - YOKE ASSEMBLY F815817 Page Page Page x_ FIGURE 7- FOOT ASSEMBLY -MODEL 113.197511 & 113.197611 FIGURE 8 Repairs Parts MODEL NOS. 113.197411, 113.197511 AND 113.197611 Page Repairs Parts FIGURE 9- CABINET ASSEMBLY FOR MODEL 113.197411 AND 113.197511 FIGURE 10 -DRAWER ASSEMBLIES 3", 6", 10" FOR MODEL 113.197611 FIGURE 11 - MOTOR ASSEMBLY / FIGURE 12 - GUARD ASSEMBLY Index /- owner's manual SERVICE MODEL NO. J J Sold by SEARS,ROEBUCK AND CO., Chicago, IL 60684 U.S.A.