Manuals / Sears / Power Tools / Saw

Sears 113.197411, 113.197611 Personal Safety Instructions, Work Area Safety Instructions

Models: 113.197411 113.197511 113.197611

1 104

Download 104 pages 10.3 Kb

Page 5

Image 5

Safety Instructions

Read and follow all safety instructions.

Personal Safety Instructions

1.Wear safety goggles labeled "ANSI Z87.1" on the package. It means the gog-

gles meet impact standards set by the American National Standards Institute.

Regular eyeglasses are not safety goggles.

2. Wear close fitting clothes, short

sleeved shirts, and non-slip shoes. Tie up long hair. Do not wear gloves, ties, jewel- ry, loose clothing, or long sleeves. These can get caught in the spinning blade and pull body parts into the blade.

3.Wear dust mask to keep from inhaling fine particles.

4.Wear ear protectors, plugs or muffs if you use saw daily.

5.Keep good footing and balance; do not over-reach.

Work Area Safety Instructions

1.Keep children, pets, and visitors out of work area; they could be hit by a thrown

workpiece, workpiece chips or pieces of blade.

2.Turn saw off, remove yellow key, and unplug before leaving work area. Do not leave until blade has stopped spinning.

3.Make work area child-proof: remove yellow key to prevent accidental start-up; store key out of sight and reach; lock work area.

4.Keep floors clean and free of sawdust, wax and other slippery materials.

5.Keep work area well lighted and un- cluttered.

6.Use saw only in dry area. Do not use in wet or damp areas.

Safety

Safety Goggles

Dust Mask

Ear Protectors

Image 5

Sears 113.197411, 113.197611, 113.197511 owner manual Personal Safety Instructions, Work Area Safety Instructions

Contents

Part No. SP5539 113.197511113.197611 Contents Major Hazards SafetySafety Symbol and Signal Words Wrong Way Feed Hazard KWARNING Work Area Safety Instructions Safety InstructionsPersonal Safety Instructions Workpiece Safety Instructions Saw Safety Instructions Blade Safety Instructions KWARNING On-Product Safety Labels Safety Identify Parts Assembly QJlIF*llfq!lt LHllLltlLllltllllltB Tools Needed For Assembly Build Cabinet Base Assembly Steps Build Foot Assemblies Shaped Slot Attach Foot Assemblies Short Assemble Side PanelsOnly Door Model without Casters Attach Door Hinges Assembly Attach Side Panels to Bottom Shelf Attach/Install Spacers Attach Skirts Center Support Upper Lower Only Drawer Model Complete Center Slide AssemblyAttach Doors Center Support Attach Handwheel Assemble Drawers Shaft has left-hand threa&. Turn nut clock- wise to loosen Mount Motor Mount Basic Saw Assembly Assembly Attach Trim Caps Adjust Leveling Feet Attach Slide Arm Supports Install Front Table Clips. Note Table will extend about Beyond Trim caps Assemble Table Lock Mechanism To Remove Drawers Only Drawer Model Alignment and AdjustmentInstall Drawers Only Drawer Model 45, -45 , 90 Controls Rip l.ock Controls Adjust Column Support Alignment and AdjustmentAlignment and Adjustment Steps Level Front Table Square Crosscut Travel Square Blade to Table for Crosscut- ting Install Blade Alignment and Adjustment Square Blade to Fence Square Blade to Table for Ripping Adjust Carriage Bearings Make Blade Parallel to Table Align Spreader to Blade Install Guard Go to Digital Display Section and follow Complete Adjustments Digital Display Error MessagesButton Functions =73 To Replace Battery Install Battery Miter Encoder Align Encoders Bevel Encoder Set Zero Reference Points For Bevel, Miter, and Elevation Set Zero Reference Point For Out-Rip Set Zero Reference Point For Rip Conversion Table Power Supply Motor Specifications Electrical Connections Motor Protection & Reset Button Before changing Motor voltage To Change Motor Voltage to 240 A.CTo avoid electric shock, unplug saw Crosscutting Crosscutting SafetyDuring crosscutting, blade teeth can Having fingers, hand or arm cut off Crosscut Kerfs Crosscuttin Step Making Crosscuts Repetitive Crosscutting Ripping Defined RippingIn-Rip and Out-Rip Positions Infeed and Outfeed Directions Workpiece Positioning Ripping Safety Pinching or binding can happen when Kickback Wrong Way Feed Ripping Pawls and Spreader Function Guard Nose Function With kerfs, workpiece could get Ripping Set-up ProcedureIf workpiece is pushed along fence Inleed Making Rip Cuts Dado Blades, Molding Heads Ripping Hints Fences Cutting AidesPush Sticks Auxiliary Fence and Push Block for Ripping Cutting Aides Straight Edge for Irregular Workpiece Cutting Aides Information for Edging Accessories SafetyInformation for Dado Edging without an auxiliary fence Lower Blade Guard Jam in fence or table kerfs AccessoriesLower blade guard can get caught or Cleaning MaintenanceGeneral Information Lubrication Remove screw and nut from swivel lock knob Adjustments for Wear Arm and Column Carriage Bearings Replacing Pawls Blade Changing What to Do Motor ProblemPossible Causes Troubleshooting Cutting Problem TroubleshootingSaw Problem Possible Causes Electronics Problem Troubleshooting Blank Model NOS .197411 and 113.197511 Repair Parts Always order by Part Number Not by Key Number Repair Parts Model NOS .197411 and 113.197611 Base and Column Assembly Model NOS .197411 and 113.197511 Model NOS .197411 and 113.197611 Parts List for Craftsman 10 Electronic Radial SAW Model NOS .197411 and 113.197511 Part Model NOS .197411 and 113.197611 and 113,197511 Repair Parts ARM Assembly Table Assembly Foot Assembly Model 113.197511 Model NOS .197411, 113.197511 Model NOS .197411, 113.197511 Repairs Parts Repairs Parts Cabinet Assembly for Model 113.197411 Model For Motor Assembly Guard Assembly Index Pail No. SP5539 Sold by SEARS, Roebuck and CO., Chicago, IL 60684 U.S.A113.197411