Kwarning, On-Product Safety Labels | Sears 113.197411, 113.197611

Safety

On-Product Safety Labels

There are several safety labels on the saw.

They alert the user to hazards explained in the manual and remind the user how to avoid the hazard.

Note where they are located on the saw. Read and follow the safety information

and instructions in these labels. Refer to

the manual for detailed explanations and instructions.

On the outfeed side of the guard is this

safety label to alert you to wrong way feed:

On the infeed side of the guard is this

safety label to alert you to kickback, and

to remind you to lower the guard nose

(hold down) for ripping:

ADANGERi

kWARNING

KICKBACKI!II_

Image 8

Sears 113.197411, 113.197611, 113.197511 owner manual Kwarning, On-Product Safety Labels

Contents

Part No. SP5539 113.197511113.197611 Contents Major Hazards SafetySafety Symbol and Signal Words KWARNING Wrong Way Feed Hazard Work Area Safety Instructions Safety InstructionsPersonal Safety Instructions Saw Safety Instructions Workpiece Safety Instructions Blade Safety Instructions On-Product Safety Labels KWARNING Safety Assembly Identify Parts QJlIF*llfq!lt LHllLltlLllltllllltB Tools Needed For Assembly Assembly Steps Build Cabinet Base Build Foot Assemblies Shaped Slot Attach Foot Assemblies Short Assemble Side PanelsOnly Door Model without Casters Assembly Attach Door Hinges Attach/Install Spacers Attach Side Panels to Bottom Shelf Attach Skirts Center Support Upper Lower Only Drawer Model Complete Center Slide AssemblyAttach Doors Center Support Assemble Drawers Attach Handwheel Mount Motor Shaft has left-hand threa&. Turn nut clock- wise to loosen Assembly Mount Basic Saw Assembly Adjust Leveling Feet Attach Trim Caps Install Front Table Attach Slide Arm Supports Clips. Note Table will extend about Beyond Trim caps Assemble Table Lock Mechanism To Remove Drawers Only Drawer Model Alignment and AdjustmentInstall Drawers Only Drawer Model Controls 45, -45 , 90 Rip l.ock Controls Adjust Column Support Alignment and AdjustmentAlignment and Adjustment Steps Level Front Table Square Crosscut Travel Install Blade Square Blade to Table for Crosscut- ting Alignment and Adjustment Square Blade to Fence Square Blade to Table for Ripping Adjust Carriage Bearings Make Blade Parallel to Table Install Guard Align Spreader to Blade Complete Adjustments Go to Digital Display Section and follow Error Messages Digital DisplayButton Functions =73 Install Battery To Replace Battery Align Encoders Miter Encoder Set Zero Reference Points For Bevel, Miter, and Elevation Bevel Encoder Set Zero Reference Point For Rip Set Zero Reference Point For Out-Rip Conversion Table Motor Specifications Power Supply Motor Protection & Reset Button Electrical Connections Before changing Motor voltage To Change Motor Voltage to 240 A.CTo avoid electric shock, unplug saw Crosscutting Safety CrosscuttingDuring crosscutting, blade teeth can Having fingers, hand or arm cut off Crosscuttin Crosscut Kerfs Making Crosscuts Step Repetitive Crosscutting Ripping Ripping DefinedIn-Rip and Out-Rip Positions Infeed and Outfeed Directions Ripping Safety Workpiece Positioning Kickback Pinching or binding can happen when Ripping Wrong Way Feed Guard Nose Function Pawls and Spreader Function With kerfs, workpiece could get Ripping Set-up ProcedureIf workpiece is pushed along fence Making Rip Cuts Inleed Ripping Hints Dado Blades, Molding Heads Cutting Aides FencesPush Sticks Auxiliary Fence and Push Block for Ripping Cutting Aides Cutting Aides Straight Edge for Irregular Workpiece Information for Edging Accessories SafetyInformation for Dado Lower Blade Guard Edging without an auxiliary fence Jam in fence or table kerfs AccessoriesLower blade guard can get caught or Maintenance CleaningGeneral Information Lubrication Adjustments for Wear Remove screw and nut from swivel lock knob Carriage Bearings Arm and Column Blade Changing Replacing Pawls What to Do Motor ProblemPossible Causes Troubleshooting Troubleshooting Cutting ProblemSaw Problem Possible Causes Troubleshooting Electronics Problem Blank Repair Parts Model NOS .197411 and 113.197511 Repair Parts Always order by Part Number Not by Key Number Model NOS .197411 and 113.197611 Base and Column Assembly Model NOS .197411 and 113.197511 Parts List for Craftsman 10 Electronic Radial SAW Model NOS .197411 and 113.197611 Model NOS .197411 and 113.197511 Model NOS .197411 and 113.197611 and 113,197511 Part Repair Parts ARM Assembly Table Assembly Foot Assembly Model 113.197511 Model NOS .197411, 113.197511 Repairs Parts Model NOS .197411, 113.197511 Repairs Parts Cabinet Assembly for Model 113.197411 For Model Motor Assembly Guard Assembly Index Pail No. SP5539 Sold by SEARS, Roebuck and CO., Chicago, IL 60684 U.S.A113.197411