English
Fitting procedure |
|
|
|
|
|
|
|
|
1. Confirm the strength of the proposed fitting location |
| A |
|
| ||||
The weight of the wall hanging bracket is approximately 3 kg (6.6 |
|
|
|
|
|
|
| |
|
|
| 480 (18 57/64) |
|
| |||
lb.). When fitted to the LCD TV, the total weight is approximately |
|
|
| 440 (17 21/64) |
|
| ||
|
|
|
|
|
|
|
| |
23 kg (50.7 lb.) (32”) or approximately 18 kg (39.7 lb.) (26”). |
|
|
| 176 (6 59/64) | 163 (6 27/64) |
|
| |
Check the wall strength at the 6 attachment locations by referring |
|
|
|
|
|
|
|
|
to the dimension drawing of the wall hanging bracket (given at | (1232551/64) | (112801/64) |
| 118 89.5 | 41/64)(4 (3 17/32) | 121120 | (449/64)47/64) | B |
There are 12 holes in the wall hanging bracket. |
| |||||||
right), and provide adequate reinforcement if strength is not |
|
|
|
|
|
|
|
|
sufficient. |
|
| LCD TV |
|
|
|
|
|
Note |
|
| external |
|
| 216 (8 1/2) |
|
|
|
| profile |
|
|
|
| ||
|
|
|
|
|
|
| ||
If the wall material is wood, and adequate attachment strength |
|
|
|
|
|
| (4 |
|
|
|
|
|
|
|
|
| |
cannot be ensured by fastening at the 6 points at right, use as | C | 23(29/32) |
|
|
| 23 | (29/32) |
|
many spare holes as necessary. However, exercise care because |
|
|
|
| ||||
|
|
|
|
|
|
|
| |
some wall materials may crack if screws are located too close |
|
| Wall hanging bracket | Wall attachment holes (at 6 points) | ||||
together. The following dimensions are important. Do not fit at |
|
| ||||||
any location where these dimensions cannot be secured. |
|
| ∗ Be sure to fit screws and tighten securely. | |||||
|
|
| ||||||
Dimensions of clearance required around wall hanging bracket | ∗ Provide spacing for the LCD TV of at least 100 | |||||||
|
|
|
|
|
|
|
| mm (3 15/16 inches) to the top and right side, at |
|
|
| A |
| B | C |
| |
|
|
|
|
| least 300 mm (11 13/16 inches) to the left side, | |||
|
|
|
|
|
|
|
| |
| 32" | 1000 | (39 | 3/8) | 558 (21 31/32) | 135 (5 5/16) |
| |
|
| at least 100 mm (3 15/16 inches) to the bottom | ||||||
|
|
|
|
|
|
|
| |
| 26" | 844 | (33 | 15/64) | 478 (18 13/16) | 135 (5 5/16) | Unit: mm (inches) | and at least 42 mm (1 21/32 inches) to the rear. |
|
|
|
|
|
|
|
|
|
2. Fit wall hanging bracket to wall
•Fit so that the arrow marks on the wall hanging bracket point upward.
•If the wall consists of a material such as concrete and bolts or nuts must be embedded beforehand, determine the hole positions by aligning using the actual wall hanging
bracket, or calculate hole positions based on the dimension drawing, and then embed “M6” bolts or nuts. When embedding bolts, locate so that the bolts protrude from the wall by 10 to 15 mm (25/64 to 19/32 inches).
(1)Fasten the screw at the top center hole first.
(2)Using a level, correct any bracket inclination, and then fasten screws at the remaining 5 locations.
Note Use commercially available M6 screws suited to the wall surface material
(wood, steel frame, concrete etc.) for fitting the bracket to the wall.
3. Prepare the LCD TV
∗Remove the TV stand from the LCD TV. Carefully store the removed TV stand.
Fit the insulation spacers to the LCD TV.
Place the LCD TV unit face down on a blanket or other soft cloth that is clean and free of debris, and follow the procedure below.
(1) Remove the terminal cover at the lower center of the TV’s backside.
∗Refit the removed terminal cover after
wiring.
(2)Affix the included cover stickers (1 each for left and right) to the stand pole holes on the bottom of the TV. (Peel off the backing paper and affix the cover stickers to cover the holes.)
(3)Fix the included Allen head countersunk screws, the dished toothed washers and insulation spacers (4 sets) into the insulation spacer fastening screw holes using the included Allen wrench as shown at right.
Insulation spacer fastening screw hole
Remove the TV stand.
Remove the screws (4 pcs).
Stand pole hole
Terminal cover
Cover sticker
Fit into the lower hole.
1Allen head countersunk screw
2Dished toothed washer
3Insulation spacer
4 Allen wrench
4
