Manual Fine Adjustment for AWC (ATW)

You can set the white balance items manually.

1.To set MASK SET, proceed as described in steps 2 to 4 of “ALC mode with SUPER-D2 OFF and ELC mode”.

2.Move the cursor to R.

3.Press L or M to obtain the optimum amount of red gain.

4.Move the cursor to B.

5.Press L or M to obtain the optimum amount of blue gain.

Note: When you need to set MASK SET, re-adjust to obtain the optimum amount of red and blue gain.

8. Motion Detector Setting (MOTION DET)

The motion detector detects the moving objects in the scene by monitoring changes in brightness level. You can select the level of sensitivity for motion detection.

When this camera is connected to a compatible intelligent CCTV system, the camera trans- mits an alarm signal by multiplexing it with the video signal.

1.Move the cursor to MOTION DET and select ON.

The factory default setting is OFF.

2.Press I. The MOTION DETECT menu appears on the monitor screen.

** MOTION DETECT **

LEVEL

....I....

 

-

+

DISPLAY MODE

 

ALARM

OFF

 

MASK SET

 

 

RET END

 

 

3.Move the cursor to MASK SET and press I. MASK SET lets you set 48 mask areas. To set MASK SET, proceed as described in steps 2 to 4 of “ALC mode with SUPER-D2 OFF and ELC mode”.

4.Move the cursor to ALARM and select ON or OFF to set the alarm for DISPLAY MODE. Note: When using the WV-RM70, WV-CU550 series, WV-CU161 or WV-CU360 controller

with this model, select OFF for ALARM.

5.Move the cursor to DISPLAY MODE and press I to see the current setting. The masks that detect the brightness changes start blinking.

6.To raise detection sensitivity, press I to return to the MOTION DETECT menu.

7.To obtain the optimum detection level, move the “I” cursor to adjust the level.

8.Repeat the procedures above to obtain a satisfactory setting.

Notes:

When the camera is not used in a Panasonic Intelligent CCTV System, select OFF. Otherwise, video equipment may malfunction because of the alarm signal misinterpreta- tion for a time code signal.

The motion detector may malfunction when the lightning equipment continuously turns on and off, or when ELC mode is selected for ALC/ELC.

Set MASK SET over the areas where leaves or curtains etc. are swaying.

Adjust the detection level on the menu to prevent misinterpretation under low light con- ditions with noise.

It takes about 0.2 seconds for the alarm signal to reach the VCR’s alarm terminal after the camera detects the moving object.

The motion detector is not specifically intended to prevent theft or fire.

9.Lens Drive Signal Selection (LENS DRIVE)

This item is used to select the type of auto iris lens drive signal to be supplied to the lens from the auto iris lens connector.

1.Move the cursor to LENS DRIVE. The factory default setting is DC.

2.Select DC if you are using the auto iris lens that requires a DC drive signal. Select VIDEO if you are using the auto iris lens that requires a video drive signal.

10. Special Menu

This menu lets you adjust and set up the video signal of the camera to meet your require-

ments.

 

 

 

 

 

 

 

 

 

 

 

Move the cursor to END in the bottom

 

 

 

 

 

 

 

 

 

line of

the CAM

SET UP menu and

 

** CAM SET UP **

** SPECIAL **

 

press

L and

M simultaneously

CAMERA ID

 

OFF

UP SIDE DOWN OFF

 

ALC/ELC

 

ALC

 

SHUTTER

 

---

 

CHROMA GAIN

....I....

(holding down L and press M) for 2

AGC

 

ON(DNR-H)

AP GAIN

....I....

SENS UP

 

OFF

 

PEDESTAL

.I

seconds or more. The SPECIAL menu

SYNC

 

INT

 

HUE

.I

appears on the monitor screen.

WHITE BAL

 

ATW1

 

-

+

MOTION DET

OFF

 

BW

OFF

 

 

 

 

LENS DRIVE

DC

 

BURST(BW)

ON

 

 

 

 

 

 

 

 

 

 

CAMERA RESET /PUSH SW

 

 

 

 

END

 

SET UP ENABLE

RET END

 

 

10-1. Camera Picture Upside Down Positioning (UP SIDE DOWN)

1.Move the cursor to UP SIDE DOWN.

2.Select ON when you want to turn the picture upside down.

10-2. Chroma Level Setting (CHROMA GAIN)

1.Move the cursor to CHROMA GAIN.

2.While observing the vectorscope or color video monitor, move the “I” cursor to adjust the chroma level.

10-3. Aperture Gain Setting (AP GAIN)

1.Move the cursor to AP GAIN.

2.While observing the waveform monitor or color video monitor, move the “I” cursor to adjust the aperture gain level.

10-4. Pedestal Level Setting (PEDESTAL)

1.Move the cursor to PEDESTAL.

2.While observing the waveform monitor or color video monitor, move the “I” cursor to adjust the pedestal level (black level).

10-5. Chroma Phase (Hue) Setting (HUE)

1.Move the cursor to HUE.

2.While observing the vectorscope or color video monitor, move the “I” cursor to adjust

the hue (chroma phase) level.

10-6 BW

This function lets you automatically switch from color to black-and-white pictures in low light conditions such as at night.

Page 10
Image 10
Panasonic WV-CP474, WV-CP470 Motion Detector Setting Motion DET, Lens Drive Signal Selection Lens Drive, Special Menu