Manuals / Patton electronic / Computer Equipment / Network Router

Patton electronic manual Model 4520 & 4110 Series Getting Started Guide, Installation

Models: 4110

1 66

Page 39

Model 4520 & 4110 Series Getting Started Guide						3 • Installation

Figure 18. Connecting to a host (cross-over cable required for SmartNode 4110 Series only)

Installing the gateway router

Page 39

Image 39

Patton electronic manual Model 4520 & 4110 Series Getting Started Guide, Installation, Installing the gateway router

Contents

Technical Support +1 301 SmartNode 4520 & 4110 SeriesVoIP Gateway Routers Getting Started Guide7622 Rickenbacker Drive Gaithersburg, MD 20879 USA tel +1 301 Compliance information ContentsContents InstallationMonitoring Status SpecificationsContents 4 Getting started with the SmartNodeCabling Port pin-outsModel 4520 & 4110 Series Getting Started Guide Model 4520 & 4110 Series Getting Started Guide ContentsCE notice ServiceCompliance information Radio and TV interferenceModel 4520 & 4110 Series Getting Started Guide Compliance informationAbout this guide AudienceStructure Safety when working with electricity PrecautionsPlace the unit on a ﬂat surface and ensure free air circulation Preventing electrostatic discharge damageGeneral observations Clean the case with a soft slightly moist anti-static clothGeneral conventions Typographical conventions used in this documentMeaning Mouse conventionsThe following conventions are used when describing mouse actions ConventionModel 4520 & 4110 Series Getting Started Guide About this guideChapter 1 General information Chapter contentsSmartNode Series VoIP routers overview SmartNode 4520 Series router The SmartNode 4520 Series rear panel ports are described in table Ports descriptionsNote If an error occurs, all LEDs will ﬂash once per second LED descriptionsSmartNode 4110 Series router The SmartNode 4110 Series rear panel ports are described in table Ports descriptionsFigure 7. SmartNode 4110 Series front panels LED descriptionsEthernet each port Link Lit when Ethernet link is up 1 General information Model 4520 & 4110 Series Getting Started GuideSmartNode Series VoIP routers overview Chapter Applications OverviewChapter contents Introduction Applications for SmartNode 4110 SeriesH.323 terminal media gateway Figure 10. BRI to FXS extension Application-Private line automatic ringdown PLARApplication-Enterprise campus BRI to FXS telephony extension Figure 9. FXS to FXS extensionFigure 11. Toll bypass Application-PBX toll bypass gatewayApplication-Point-to-point WAN QoS Switch Applications for SmartNode 4520 SeriesApplication-Desktop or LAN segment QoS Applications in combination with FXO models Application-SOHO off-premise extensionApplications for SmartNode 4520 Series Installation Chapter contentsChapter Planning the installation Create a network diagram see section “Network information” on pageVerify power source reliability see section “Power source” on page Date Installation checklistTask Veriﬁed byNetwork information Network DiagramPower source Site logMounting the gateway router Installing the gateway routerConnecting cables Location and mounting requirementsFigure 14. Analog FXS connection Installing an interface cable on the router’s FXS interface portInstalling the gateway router Figure 15. RJ-11 pinout diagram Table 7. RJ-11 socketSignal 3 InstallationNote Pins not listed are not used Installing the Ethernet cable3 Installation Installing the gateway routerModel 4520 & 4110 Series Getting Started Guide 5. Verify that the green Power LED is lit see ﬁgure Installing the power cordChapter contents Chapter 4 Getting started with the SmartNodeIntroduction Figure 20. Steps for setting up a new SmartNodePower connection and default conﬁguration 1. Conﬁgure IP addressConnect with the serial interface Changing the IP address Login3. Load conﬁguration 2. Connect the SmartNode to the networkAdditional information Additional informationChapter contents Chapter 5 Monitoring StatusModel 4520 & 4110 Series Getting Started Guide Status LEDsFigure 23. SmartNode 4520 Series front panels 5 Monitoring StatusStatus LEDs Figure 24. SmartNode 4110 Series front panelsModel 4520 & 4110 Series Getting Started Guide 5 Monitoring StatusPower DescriptionVoIP Link Chapter contents Chapter 6 Contacting Patton for assistanceContact information Warranty Service and Returned Merchandise Authorizations RMAsWarranty coverage Out-of-warranty servicePatton Electronics Company Return for credit policyRMA numbers Shipping instructionsWarranty Service and Returned Merchandise Authorizations RMAs 6 Contacting Patton for assistanceModel 4520 & 4110 Series Getting Started Guide Chapter contents Appendix A SpeciﬁcationsFax and modem support Voice processing signalling dependentVoice connectivity ConnectivityVoice Signalling IP servicesVoice Routing-Session Router Operating Environment DimensionsOperating temperature ManagementSee table WeightPower supply Power dissipationA Specifications Power supplyModel 4520 & 4110 Series Getting Started Guide Chapter contents Appendix B CablingSerial console Figure 25. Connecting a serial terminalIntroduction Figure 26. Ethernet cross-over Ethernet 10Base-T and 100Base-TB Cabling Analog FXSFigure 28. Connecting an FXS device Figure 27. Ethernet straight-throughChapter contents Appendix C Port pin-outsSignal Console portEthernet 10Base-T and 100Base-T port FXS port