Patton electronic 4960 Series G.SHDSL Daughter Card (if applicable)

G.SHDSL Daughter Card (if applicable) 53

SmartNode 4960 Getting Started Guide B • Specifications

G.SHDSL Daughter Card (if applicable)

Note For information on conﬁguring the G.SHDSL daughter card,

see Chapter 5, “G.SHDSL Basic Conﬁguration” on page 38.

Table 12. G.SHDSL Daughter Card Speciﬁcations

Factor Specs

DSL • ITU-T G.991.2 (and Amendment 2)

• ITU-T G.991.2, Annex A, B, F, G

• Upgradable to ITU-T G.shdsl.bis—Annex F and G

• G.991.2 2/4 (1/2 pair) operation

• G.994.1 (G.hs) (per G.991.2)

• ITU-T G.991.2 Section E.9

(TPS-TC for ATM transport)

• ITU-T G.991.2 Section E.11

(TPS-TC for PTM transport)

DSL Connection RJ-11/12 (2-wire)

Management • I.610 OAM F4/F5

• Management interfaces: GUI and Telnet

• Software upgrade: GUI and TFTP

ATM Support • Classical IPoA (RFC 1577/2225)

• PPPoE Client (over ATM) (RFC 2516)

• IPoA (RFC 2684/1483)

• ATM AAL5 encapsulation

• Max. 8 PVCs

• User selectable VC MUX and LLC MUX (default)

• Conﬁgurable auto-connection

• ATM QoS: UBR (default), CBR, and VBR-rt, VBR-nrt,

UBR: per VC queuing

• Auto-conﬁguration: TR-037 & ILMI 4.0

Interworking/Interoperability • G.SHDSL Interoperability:

-Alcatel

-NEC

-Lucent Anymedia

-Lucent Stinger

• BRAS Interoperability:

-Cisco

-Redback

Contents

Main SmartNode 4960 Series For Quick Getting Started Guide Page Summary Table of Contents Table of Contents Page Page List of Figures List of Tables About this guide Audience Structure Precautions Safety when working with electricity General observations Typographical conventions used in this document Table 1. General conventions Convention Meaning Page SmartNode 4960 overview Page SmartNode 4960 rear panel Figure 2. SN4960 rear panel The SmartNode 4960 rear panel ports are described in table 4. Power SmartNode 4960 front panel Figure 3 shows SmartNode 4960 front panel LEDs, the LED denitions are listed in table 5. Figure 3. SmartNode 4960 front panel Page Page ApplicationEdge intelligence of enterprise communication ApplicationMulti-service ISDN Internet telephony IAD Page Chapter 3 SmartNode installation Planning the installation Site log Network information Network Diagram IP related information Installing the gateway router Placing the SmartNode Installing cables Connecting the PRI Connecting the 10/100/1000Base-T Ethernet LAN and WAN cables Connecting the power supply Chapter 4 Initial conguration 1. Connecting the SmartNode to your laptop PC 2. Conguring the desired IP address Factory-default IP settings Login Changing the WAN IP address 3. Connecting the SmartNode to the network 4. Loading the conguration (optional) Bootloader Start Bootloader Start-up with factory conguration Load a new application image (SmartWare) via TFTP gateway Download it after starting up SmartWare with the following command: Example: Downloading and storing a new application image (SmartWare) Load a new application image (SmartWare) via the serial link Additional information Chapter 5 G.SHDSL Basic Conguration Line Setup Conguring PPPoE Conguration Summary Setting up permanent virtual circuits (PVC) Using PVC channels in bridged Ethernet mode Using PVC channels with PPPoE Diagnostics Troubleshooting DSL Connections Chapter 6 Contacting Patton for assistance Contact information Patton support headquarters in the USA Alternate Patton support for Europe, Middle East, and Africa (EMEA) Warranty Service and Returned Merchandise Authorizations (RMAs) Warranty coverage Out-of-warranty service Returns for credit Return for credit policy RMA numbers Shipping instructions Appendix A Compliance information Compliance EMC Safety PSTN Regulatory Radio and TV Interference Industry Canada Notice CE Declaration of Conformity Appendix B Specications DSP Voice connectivity Data connectivity Voice processing (signalling dependent) Fax and modem support Voice signalling Voice routingsession router IP services Management System Physical G.SHDSL Daughter Card (if applicable) see Chapter 5, G.SHDSL Basic Conguration on page 38. - - - - - - Identication of the SmartNode devices via SNMP Page Console Ethernet E1 PRI T1 PRI Page This section provides pin-out information for the ports of the SmartNode. Console port Conguration settings: 9600 bps, 8 bits, no parity, 1 stop bit, no ow control Ethernet PRI port G.SHDSL port Page The factory conguration settings for SmartNode 4960 are as follows: Appendix F End user license agreement End User License Agreement 1. Denitions 2. Title 3. Term 4. Grant of License 6. Termination 7. Other licenses